PIC24FJ128GA310 datasheet(83/406 Pages) MICROCHIP

83 / 406 page

 2010-2011 Microchip Technology Inc.

DS39996F-page 83

PIC24FJ128GA310 FAMILY

6.0

FLASH PROGRAM MEMORY

The PIC24FJ128GA310 family of devices contains

internal Flash program memory for storing and execut-

ing application code. The program memory is readable,

writable and erasable. The Flash can be programmed

in four ways:

• In-Circuit Serial Programming™ (ICSP™)

• Run-Time Self-Programming (RTSP)

•JTAG

• Enhanced In-Circuit Serial Programming

(Enhanced ICSP)

ICSP allows a PIC24FJ128GA310 family device to be

serially programmed while in the end application circuit.

This is simply done with two lines for the programming

clock and programming data (named PGECx and

PGEDx, respectively), and three other lines for power

(VDD), ground (VSS) and Master Clear (MCLR). This

allows customers to manufacture boards with

unprogrammed devices and then program the

microcontroller just before shipping the product. This

also allows the most recent firmware or a custom

firmware to be programmed.

RTSP is accomplished using TBLRD (table read) and

TBLWT

(table write) instructions. With RTSP, the user

may write program memory data in blocks of 64 instruc-

tions (192 bytes) at a time and erase program memory

in blocks of 512 instructions (1536 bytes) at a time.

6.1

Table Instructions and Flash

Programming

Regardless of the method used, all programming of

Flash memory is done with the table read and write

instructions. These allow direct read and write access to

the program memory space from the data memory while

the device is in normal operating mode. The 24-bit target

address in the program memory is formed using the

TBLPAG<7:0> bits and the Effective Address (EA) from

a W register, specified in the table instruction, as shown

in Figure 6-1.

The TBLRDL and the TBLWTL instructions are used to

read or write to bits<15:0> of program memory.

TBLRDL

and TBLWTL can access program memory in

both Word and Byte modes.

The TBLRDH and TBLWTH instructions are used to read

or write to bits<23:16> of program memory. TBLRDH

and TBLWTH can also access program memory in Word

or Byte mode.

FIGURE 6-1:

ADDRESSING FOR TABLE REGISTERS

Note:

This data sheet summarizes the features of

this group of PIC24F devices. It is not

intended to be a comprehensive reference

source. For more information, refer to the

“PIC24F

Family

Reference

Manual”

Section

“Program

Memory”

(DS39715). The information in this data

sheet supersedes the information in the

FRM.

Program Counter

24 Bits

Program

TBLPAG Reg

8 Bits

Working Reg EA

16 Bits

Using

Byte

24-Bit EA

1/0

Select

Table

Instruction

Counter

Using

User/Configuration

Space Select

PIC24FJ128GA310 bảng dữ liệu(PDF) 83 Page - Microchip Technology

PIC24FJ128GA310 bảng dữ liệu(HTML) 83 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL