STM32F103RCT6 datasheet(20/130 Pages) STMICROELECTRONICS

20 / 130 page

Description

STM32F103xC, STM32F103xD, STM32F103xE

20/130

Doc ID 14611 Rev 8

General-purpose timers (TIMx)

There are up to 4 synchronizable general-purpose timers (TIM2, TIM3, TIM4 and TIM5)

embedded in the STM32F103xC, STM32F103xD and STM32F103xE performance line

devices. These timers are based on a 16-bit auto-reload up/down counter, a 16-bit prescaler

and feature 4 independent channels each for input capture/output compare, PWM or one-

pulse mode output. This gives up to 16 input captures / output compares / PWMs on the

largest packages.

The general-purpose timers can work together with the advanced-control timer via the Timer

Link feature for synchronization or event chaining. Their counter can be frozen in debug

mode. Any of the general-purpose timers can be used to generate PWM outputs. They all

have independent DMA request generation.

These timers are capable of handling quadrature (incremental) encoder signals and the

digital outputs from 1 to 3 hall-effect sensors.

Basic timers TIM6 and TIM7

These timers are mainly used for DAC trigger generation. They can also be used as a

generic 16-bit time base.

Independent watchdog

The independent watchdog is based on a 12-bit downcounter and 8-bit prescaler. It is

clocked from an independent 40 kHz internal RC and as it operates independently from the

main clock, it can operate in Stop and Standby modes. It can be used either as a watchdog

to reset the device when a problem occurs, or as a free running timer for application timeout

management. It is hardware or software configurable through the option bytes. The counter

can be frozen in debug mode.

Window watchdog

The window watchdog is based on a 7-bit downcounter that can be set as free running. It

can be used as a watchdog to reset the device when a problem occurs. It is clocked from the

main clock. It has an early warning interrupt capability and the counter can be frozen in

debug mode.

SysTick timer

This timer is dedicated to real-time operating systems, but could also be used as a standard

down counter. It features:

●

A 24-bit down counter

●

Autoreload capability

●

Maskable system interrupt generation when the counter reaches 0.

●

Programmable clock source

2.3.18

I²C bus

Up to two I²C bus interfaces can operate in multimaster and slave modes. They can support

standard and fast modes.

They support 7/10-bit addressing mode and 7-bit dual addressing mode (as slave). A

hardware CRC generation/verification is embedded.

They can be served by DMA and they support SMBus 2.0/PMBus.

STM32F103RCT6 bảng dữ liệu(PDF) 20 Page - STMicroelectronics

STM32F103RCT6 bảng dữ liệu(HTML) 20 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL