công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

DS38C86AVB bảng dữ liệu(PDF) 6 Page - Texas Instruments

tên linh kiện DS38C86AVB
Giải thích chi tiết về linh kiện  DS38C86A CMOS BTL 9-Bit Latching Data Transceiver
PDF  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  TI1 [Texas Instruments]
Trang chủ  http://www.ti.com
Logo TI1 - Texas Instruments

DS38C86AVB bảng dữ liệu(HTML) 6 Page - Texas Instruments

Back Button DS38C86AVB Datasheet HTML 2Page - Texas Instruments DS38C86AVB Datasheet HTML 3Page - Texas Instruments DS38C86AVB Datasheet HTML 4Page - Texas Instruments DS38C86AVB Datasheet HTML 5Page - Texas Instruments DS38C86AVB Datasheet HTML 6Page - Texas Instruments DS38C86AVB Datasheet HTML 7Page - Texas Instruments DS38C86AVB Datasheet HTML 8Page - Texas Instruments DS38C86AVB Datasheet HTML 9Page - Texas Instruments DS38C86AVB Datasheet HTML 10Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 6 / 12 page
background image
AC Electrical Characteristics (Note 6) (Continued)
T
A = 0˚C to +70˚C, VCC =5V ± 10%
DRIVER (REN = 0V for all conditions)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
RECEIVER
t
PLZ
T/R to An
Disable Time
LE = V
CC, Bn = 2.1V, CD = 0V
3.0
6.0
9.0
ns
t
PZL
Enable Time
(
Figures 10, 11)
3.0
5.0
9.0
ns
t
PHZ
Disable Time
LE = V
CC, Bn = 1.1 CD = 0V
3.0
7.3
12.0
ns
t
PZH
Enable Time
(
Figures 8, 9)
3.0
5.5
12.0
ns
t
SKEW
LE to An, Same Package
(Note 7)
0.6
2.5
ns
Bn to An, Same Package
(Note 7)
0.7
2.5
ns
RECEIVER TIMING REQUIREMENTS (
Figure 7)
t
S
Bn to LE (Set-Up Time)
CD = 0V, T/R = 0V
3ns
t
H
LE to Bn (Hold Time)
1
ns
t
PW
LE Pulse Width
5
ns
PARAMETERS NOT TESTED
C
OUTPUT
Capacitance at Bn
(Note 9)
3
pF
t
NR
Noise Rejection
(Note 10)
1
ns
Note 1: “Absolute Maximum Ratings” are these beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should
be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation.
Note 2: All input and/or output pins shall not exceed VCC+0.5V and shall not exceed the absolute maximum rating at any time, including power-up and power-down.
This prevents the ESD structure from being damaged due to excessive currents flowing from the input and/or output pins to QVCC and VCC. There is a diode between
each input and/or output to VCC which is forward biased when incorrent sequencing is applied. LI and Bn pins do not have power sequencing requirements with
respect to VCC and QVCC. Furthermore, the difference between VCC and QVCC should never be greater than 0.5V at any time including power-up.
Note 3: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified.
All typical values are specified under these conditions: VCC = 5V and TA = 25˚C, unless otherwise stated.
Note 4: Only one output should be shorted at a time, and duration of the short should not exceed one second.
Note 5: Referenced to appropriate signal ground. Do not exceed maximum power dissipation of package.
Note 6: Input waveforms shall have a rise and fall time of 3 ns.
Note 7: tSKEW is the absolute value defined as the difference seen in propagation delay between drivers (receivers) in the same package with identical load
conditions.
Note 8: This parameter is tested using TDR techniques described in 1194.0 BTL Backplane Design Guide.
Note 9: This parameter is tested during device characterization. The measurements revealed that the part will reject 1 ns pulse width.
Note 10: Futurebus+ transceivers are required to limit bus signal rise and fall times to no faster then 0.5 V/ns, measured between 1.3V to 1.8V (approximately 20%
to 80% of the nominal voltage swing). The rise and fall times are measured with a transceiver loading equivalent to 12.5
Ω ties to +2.1 VDC.
Note 11: Capacitance includes jig and probe capacitance.
Note 12: All pins meet 2 kV typical, one device failure observed between An and QVCC in ESD rel sample.
Pin Description
Pin Name
No. of
Pins
Input/Output
Description
A0–A8
9
I/O
TTL driver input and TRI-STATE receiver output
ACLK
1
I
Clock input for latch mode
B0–B8
9
I/O
BTL receiver input and driver output
B0 GND–B8 GND
9
NA
Driver output ground reduces ground bounce due to high current switching of
driver outputs. (Note 11)
CD
1
I
Chip disable
GND
2
NA
Ground reference for switching circuits (Note 11)
LE
1
I
Latch enable
LI
1
NA
Power supply for live insertion. Boards that require live insertion should connect
LI to the live insertion pin on the connector. (Note 12)
NC
9
NA
No connect
QGND
1
NA
Ground reference for receiver input bandgap reference and non-switching
circuits (Note 12)
QV
CC
1
NA
Power supply for bandgap reference and non-switching circuits (Note 12)
RBYP
1
I
Register bypass enable
www.national.com
5



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com