công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

DS38C86AVB bảng dữ liệu(PDF) 2 Page - Texas Instruments

tên linh kiện DS38C86AVB
Giải thích chi tiết về linh kiện  DS38C86A CMOS BTL 9-Bit Latching Data Transceiver
PDF  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  TI1 [Texas Instruments]
Trang chủ  http://www.ti.com
Logo TI1 - Texas Instruments

DS38C86AVB bảng dữ liệu(HTML) 2 Page - Texas Instruments

  DS38C86AVB Datasheet HTML 1Page - Texas Instruments DS38C86AVB Datasheet HTML 2Page - Texas Instruments DS38C86AVB Datasheet HTML 3Page - Texas Instruments DS38C86AVB Datasheet HTML 4Page - Texas Instruments DS38C86AVB Datasheet HTML 5Page - Texas Instruments DS38C86AVB Datasheet HTML 6Page - Texas Instruments DS38C86AVB Datasheet HTML 7Page - Texas Instruments DS38C86AVB Datasheet HTML 8Page - Texas Instruments DS38C86AVB Datasheet HTML 9Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 2 / 12 page
background image
DS38C86A
CMOS BTL 9-Bit Latching Data Transceiver
General Description
The DS38C86A is a 9-bit BTL Latching Data Transceiver
designed specifically for proprietary bus interfaces. The de-
vice is implemented in CMOS technology, and delivers all of
the performance of its Bi-CMOS counterparts while consum-
ing less then half of the power supply current of the
DS3886A. The DS38C86A conforms to the IEEE 11941.1
(Backplane Transceiver Logic - BTL) Standard.
The DS38C86A incorporates an edge-triggered latch in the
driver path which can be bypassed during fall-through mode
of operation and a transparent latch in the receiver path. The
DS38C86A driver output configuration is an open drain
which allows Wired-OR connection on the bus. A unique
design reduces the bus loading to 3 pF typical. The driver
also has high sink current capability to comply with the bus
loading requirements defined within IEEE 11941.1 BTL
specification.
Backplane Transceiver Logic (BTL) is a signaling standard
that was invented and first introduced by National Semicon-
ductor, then developed by the IEEE to enhance the perfor-
mance of backplane buses. BTL transceivers feature low
output capacitance drivers to minimize bus loading, a 1V
nominal signal swing for reduced power consumption and
receivers with precision thresholds for maximum noise im-
munity. The BTL standard eliminates settling time delays that
severely limit TTL bus performance, and thus provide signifi-
cantly higher bus transfer rates. The backplane bus is in-
tended to be operated with termination resistors (selected to
match the bus impedance) connected to a 2.1V at both ends.
The low voltage is typically 1V.
The DS38C86A provides an alternative to high power Bipo-
lar and BiCMOS devices with the use of CMOS technology.
The CMOS technology enables the DS38C86A to operate at
50% of the I
CC required by the Bi-CMOS DS3886A. This can
have a major impact on system power consumption. For
example, if a backplane is 128 bits wide, 16 devices (9 bits
each) required per card. Also assume the backplane is one
rack with 20 slots. Power dissipation savings for this appli-
cation is calculated by the following equation:
P= I
CC-savings x Power supply voltage x number of devices
P = 32 mA x 5.5V x 320 = 56 Watts
The power dissipation savings may increase even more
when; the system bus is wider than 128 bits, there are
multiple racks in the system, or if the system includes a hot
backup. This may double the power dissipation savings.
Separate ground pins are provided for each BTL output
minimize induced ground noise during simultaneous switch-
ing.
The unique driver circuitry provides a maximum slew rate of
0.9V/ns which allows controlled rise and fall times to reduce
noise coupling to adjacent lines.
The transceiver’s high impedance control and driver inputs
are fully TTL compatible.
The receiver is a high speed comparator that utilizes a
Bandgap reference for precision threshold control allowing
maximum immunity to the BTL 1V signaling level.
Separate QV
CC and QGND pins are provided to minimize
the effects of high current switching noise. The receiver
output is TRI-STATE® and fully TTL compatible.
The DS38C86A supports live insertion as defined in IEEE
896.2 through the LI (Live Insertion) pin. To implement live
insertion the LI pin should be connected to the live insertion
power connector. If this function is not supported, the LI pin
must be tied to the V
CC pin. The DS38C86A also provides
glitch free power up/down protection during power sequenc-
ing.
The DS38C86A has two types of power connections in ad-
dition to the LI pin. They are the Logic V
CC (VCC) and the
Quiet V
CC (QVCC). There are two Logic VCC pins on the
DS38C86A that provide the supply voltage for the logic and
control circuitry. Multiple connections are provided to reduce
the effects of package inductance and thereby minimize
switching noise. A voltage delta between V
CC and QVCC
should never exceed ±0.5V because of ESD circuitry.
When CD (Chip Disable) is high, An is in high impedance
state and Bn is high. To transmit data (An to Bn), the T/R
signal is high.
When RBYP is high, the positive edge triggered flip-flop is in
the transparent mode. When RBYP is low, the positive edge
of the ACLK signal clocks the data.
In addition, the ESD circuitry between the V
CC pins and all
other pins except for BTL I/O’s and LI pins requires that any
voltage on these pins should not exceed the voltage on V
CC
+0.5V.
There are three different types of ground pins on the
DS38C86A;
the
logic
ground
(GND),
BTL
grounds
(B0GND–B8GND) and the Bandgap reference ground
(QGND). All of these ground reference pins are isolated
within the chip to minimize the effects of high current switch-
ing transients. For optimum performance the QGND should
be returned to the connector through a quiet channel that
does not carry transient switching current. The GND and
B0GND–B8GND should be connected to the nearest back-
plane ground pin with the shortest possible path.
Since many different grounding schemes could be imple-
mented and ESD circuitry exists on the DS38C86A, it is
important to note that any voltage between ground pins,
QGND, GND or B0GND–B8GND should not exceed ±0.5V
including power up/down sequencing.
The DS38C86A is offered in a 48-pin7x7 space saving
PQFP package.
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
July 1998
© 2001 National Semiconductor Corporation
DS012623
www.national.com



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com