ATmega1284P datasheet(215/380 Pages) ATMEL

215 / 380 page

215

8059D–AVR–11/09

ATmega1284P

The TWINT Flag is set in the following situations:

• After the TWI has transmitted a START/REPEATED START condition.

• After the TWI has transmitted SLA+R/W.

• After the TWI has transmitted an address byte.

• After the TWI has lost arbitration.

• After the TWI has been addressed by own slave address or general call.

• After the TWI has received a data byte.

• After a STOP or REPEATED START has been received while still addressed as a Slave.

• When a bus error has occurred due to an illegal START or STOP condition.

19.6

Using the TWI

The AVR TWI is byte-oriented and interrupt based. Interrupts are issued after all bus events, like

reception of a byte or transmission of a START condition. Because the TWI is interrupt-based,

the application software is free to carry on other operations during a TWI byte transfer. Note that

the TWI Interrupt Enable (TWIE) bit in TWCR together with the Global Interrupt Enable bit in

SREG allow the application to decide whether or not assertion of the TWINT Flag should gener-

ate an interrupt request. If the TWIE bit is cleared, the application must poll the TWINT Flag in

order to detect actions on the TWI bus.

When the TWINT Flag is asserted, the TWI has finished an operation and awaits application

response. In this case, the TWI Status Register (TWSR) contains a value indicating the current

state of the TWI bus. The application software can then decide how the TWI should behave in

the next TWI bus cycle by manipulating the TWCR and TWDR Registers.

Figure 19-10 is a simple example of how the application can interface to the TWI hardware. In

this example, a Master wishes to transmit a single data byte to a Slave. This description is quite

abstract, a more detailed explanation follows later in this section. A simple code example imple-

menting the desired behavior is also presented.

Figure 19-10. Interfacing the Application to the TWI in a Typical Transmission

The first step in a TWI transmission is to transmit a START condition. This is done by

writing a specific value into TWCR, instructing the TWI hardware to transmit a START

START

SLA+W

Data

STOP

1. Application

writes to TWCR to

initiate

transmission of

START

2. TWINT set.

Status code indicates

START condition sent

4. TWINT set.

Status code indicates

SLA+W sent, ACK

received

6. TWINT set.

Status code indicates

data sent, ACK received

3. Check TWSR to see if START was

sent. Application loads SLA+W into

TWDR, and loads appropriate control

signals into TWCR, makin sure that

TWINT is written to one,

and TWSTA is written to zero.

5. Check TWSR to see if SLA+W was

sent and ACK received.

Application loads data into TWDR, and

loads appropriate control signals into

TWCR, making sure that TWINT is

written to one

7. Check TWSR to see if data was sent

and ACK received.

Application loads appropriate control

signals to send STOP into TWCR,

making sure that TWINT is written to one

TWI bus

Indicates

TWINT set

ATmega1284P bảng dữ liệu(PDF) 215 Page - ATMEL Corporation

ATmega1284P bảng dữ liệu(HTML) 215 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL