| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TLE8262E bảng dữ liệu(PDF) 80 Page - Infineon Technologies AG |
|
|
|||||||||||||||||||||||||||||
TLE8262E bảng dữ liệu(HTML) 80 Page - Infineon Technologies AG |
|
80 / 93 page ![]() Data Sheet 80 Rev. 1.0, 2009-03-31 TLE8262E Serial Peripheral Interface 15.5.3.2 Limp Home failure encoder Table 22 describes the encoding of all possible reason to activate automatically the Limp Home output. Bits are set back to “000” when switching Limp Home off via SPI. 15.5.3.3 Test pin and failure to Limp Home configuration read out The SBC allows to read the hardware setting of the configuration that is done via the INT pin, as well as the test pin and the WD to LH bit. Table 23 describes the encoding of these informations. Table 22 Limp Home Failure Diagnosis LH2 LH1 LH0 Failure1) 00 0 No failure 00 1 V cc1µC undervoltage Time-out 0 1 0 One Watchdog failure (config 1 and 2) 0 1 1 Two consecutive Watchdog failures (config 3 and 4) 1 0 0 INIT Mode Time-out 1 0 1 Temperature shutdown at V cc1µC 1 1 0 Reset clamped 11 1 Reserved Table 23 Test pin and SBC Configuration Test2 Test1 Test0 Test Read Out1) 1) Refer also to Chapter 4.2.1 00 0 V cc1µC remains ON in SBC Restart Mode after one Watchdog failure (config 1) 00 1 V cc1µC is OFF in SBC Fail-Safe Mode after one Watchdog failure (config 2) 01 0 V cc1µC remains ON in SBC Restart Mode after two Watchdog failures (config 3) 01 1 V cc1µC is OFF in SBC Fail-Safe Mode after two Watchdog failures (config 4) 1 0 0 Software Development Mode. In case of watchdog failure V cc1µC remains ON, no reset is generated and Restart Mode or Fail-Safe Mode are not entered. 1 0 1 Software Development Mode. In case of watchdog failure V cc1µC remains ON, no reset is generated and Restart Mode or Fail-Safe Mode are not entered. 1 1 0 Software Development Mode. In case of watchdog failure V cc1µC remains ON, no reset is generated and Restart Mode or Fail-Safe Mode are not entered. 1 1 1 Software Development Mode. In case of watchdog failure V cc1µC remains ON, no reset is generated and Restart Mode or Fail-Safe Mode are not entered. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |