| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
EX128-CS100 bảng dữ liệu(PDF) 26 Page - Actel Corporation |
|
|
|||||||||||||||||||||||||||||
EX128-CS100 bảng dữ liệu(HTML) 26 Page - Actel Corporation |
|
26 / 49 page ![]() eX Family FPGAs 1- 22 v4.3 eX Family Timing Characteristics Table 1-17 • eX Family Timing Characteristics (Worst-Case Commercial Conditions, VCCA = 2.3 V, TJ = 70°C) ‘–P’ Speed ‘Std’ Speed ‘–F’ Speed Units Parameter Description Min. Max. Min. Max. Min. Max. C-Cell Propagation Delays1 tPD Internal Array Module 0.7 1.0 1.4 ns Predicted Routing Delays2 tDC FO=1 Routing Delay, DirectConnect 0.1 0.1 0.2 ns tFC FO=1 Routing Delay, FastConnect 0.3 0.5 0.7 ns tRD1 FO=1 Routing Delay 0.3 0.5 0.7 ns tRD2 FO=2 Routing Delay 0.4 0.6 0.8 ns tRD3 FO=3 Routing Delay 0.5 0.8 1.1 ns tRD4 FO=4 Routing Delay 0.7 1.0 1.3 ns tRD8 FO=8 Routing Delay 1.2 1.7 2.4 ns tRD12 FO=12 Routing Delay 1.7 2.5 3.5 ns R-Cell Timing tRCO Sequential Clock-to-Q 0.6 0.9 1.3 ns tCLR Asynchronous Clear-to-Q 0.6 0.8 1.2 ns tPRESET Asynchronous Preset-to-Q 0.7 0.9 1.3 ns tSUD Flip-Flop Data Input Set-Up 0.5 0.7 1.0 ns tHD Flip-Flop Data Input Hold 0.0 0.0 0.0 ns tWASYN Asynchronous Pulse Width 1.3 1.9 2.6 ns tRECASYN Asynchronous Recovery Time 0.3 0.5 0.7 ns tHASYN Asynchronous Hold Time 0.3 0.5 0.7 ns 2.5 V Input Module Propagation Delays tINYH Input Data Pad-to-Y HIGH 0.6 0.9 1.3 ns tINYL Input Data Pad-to-Y LOW 0.8 1.1 1.5 ns 3.3 V Input Module Propagation Delays tINYH Input Data Pad-to-Y HIGH 0.7 1.0 1.4 ns tINYL Input Data Pad-to-Y LOW 0.9 1.3 1.8 ns 5.0 V Input Module Propagation Delays tINYH Input Data Pad-to-Y HIGH 0.7 1.0 1.4 ns tINYL Input Data Pad-to-Y LOW 0.9 1.3 1.8 ns Input Module Predicted Routing Delays2 tIRD1 FO=1 Routing Delay 0.3 0.4 0.5 ns tIRD2 FO=2 Routing Delay 0.4 0.6 0.8 ns tIRD3 FO=3 Routing Delay 0.5 0.8 1.1 ns tIRD4 FO=4 Routing Delay 0.7 1.0 1.3 ns tIRD8 FO=8 Routing Delay 1.2 1.7 2.4 ns tIRD12 FO=12 Routing Delay 1.7 2.5 3.5 ns Notes: 1. For dual-module macros, use tPD + tRD1 + tPDn, tRCO + tRD1 + tPDn or tPD1 + tRD1 + tSUD, whichever is appropriate. 2. Routing delays are for typical designs across worst-case operating conditions. These parameters should be used for estimating device performance. Post-route timing analysis or simulation is required to determine actual worst-case performance. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |