PIC18F6493 datasheet(3/58 Pages) MICROCHIP

3 / 58 page

Preliminary

DS39896A-page 1

PIC18F6393/6493/8393/8493

LCD Driver Module Features:

• Direct Driving of LCD Panel

• Up to 192 Pixels: Software Selectable

• Programmable LCD Timing module:

- Multiple LCD timing sources available

- Up to four commons: Static, 1/2, 1/3 or

1/4 multiplex

- Static, 1/2 or 1/3 bias configuration

• Can Drive LCD Panel while in Sleep mode for

Low-Power Operation

Power-Managed Modes:

• Run: CPU On, Peripherals On

• Idle: CPU Off, Peripherals On

• Sleep: CPU Off, Peripherals Off

• Run mode Current Down to 14

μA Typical

• Idle mode Currents Down to 5.8

μA Typical

• Sleep mode Currents Down to 0.1

μA Typical

• Timer1 Oscillator: 1.8

μA, 32 kHz, 2V

• Watchdog Timer: 2.1

μA Typical

• Two-Speed Oscillator Start-up

Flexible Oscillator Structure:

• Four Crystal modes:

- LP: Up to 200 kHz

- XT: Up to 4 MHz

- HS: Up to 40 MHz

- HSPLL: 4-10 MHz (16-40 MHz internal)

• 4x Phase Lock Loop (available for crystal and

internal oscillators)

• Two External RC modes, Up to 4 MHz

• Two External Clock modes, Up to 40 MHz

• Internal Oscillator Block:

- Eight selectable frequencies, from 31 kHz to 8 MHz

- Provides a complete range of clock speeds

from 31 kHz to 32 MHz when used with PLL

- User-tunable to compensate for frequency drift

• Secondary Oscillator Using Timer1 at 32 kHz

• Fail-Safe Clock Monitor:

- Allows for safe shutdown of device if primary

or secondary clock fails

Peripheral Highlights:

• 12-Bit, Up to 12-Channel Analog-to-Digital (A/D)

Converter module:

- Auto-acquisition capability

- Conversion available during Sleep

• High-Current Sink/Source 25 mA/25 mA

• Four External Interrupts

• Four Input Change Interrupts

• Four 8-Bit/16-Bit Timer/Counter modules

• Real-Time Clock (RTC) Software module:

- Configurable 24-hour clock, calendar, automatic

100-year or 12,800-year, day-of-week calculator

- Uses Timer1

• Up to Two Capture/Compare/PWM (CCP) modules

• Master Synchronous Serial Port (MSSP) module

Supporting Three-Wire SPI (all four modes) and

I2C™ Master and Slave modes

• Addressable USART module:

- Supports RS-485 and RS-232

• Enhanced Addressable USART module:

- Supports RS-485, RS-232 and LIN 1.2

- Auto-wake-up on Start bit

- Auto-Baud Detect

• Dual Analog Comparators with Input Multiplexing

Special Microcontroller Features:

• C Compiler Optimized Architecture:

- Optional extended instruction set designed to

optimize re-entrant code

• 1000 Erase/Write Cycle Flash Program Memory

Typical

• Flash Retention: 100 Years Typical

• Priority Levels for Interrupts

• 8 x 8 Single-Cycle Hardware Multiplier

• Extended Watchdog Timer (WDT):

- Programmable period from 4 ms to 132s

- 2% stability over VDD and temperature

• In-Circuit Serial Programming™ (ICSP™) via Two Pins

• In-Circuit Debug (ICD) via Two Pins

• Wide Operating Voltage Range: 2.0V to 5.5V

Note:

This document is supplemented by the

“PIC18F6390/6490/8390/8490 Data Sheet”

(DS39629). See Section 1.0 “Device

Overview”.

64/80-Pin High-Performance, Flash Microcontrollers

with LCD Driver, 12-Bit ADC and nanoWatt Technology

PIC18F6493 bảng dữ liệu(PDF) 3 Page - Microchip Technology

PIC18F6493 bảng dữ liệu(HTML) 3 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58

bảng dữ liệu tải về

Link URL