| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2437 bảng dữ liệu(PDF) 113 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2437 bảng dữ liệu(HTML) 113 Page - Renesas Technology Corp |
|
113 / 746 page ![]() Rev. 1.00, 09/03, page 75 of 704 5.3.6 Software Standby Release IRQ Enable Register (SSIER) SSIER selects the IRQ pins used to recover from the software standby state. Bit Bit Name Initial Value R/W Description 7 6 5 4 3 2 1 0 SSI7 SSI6 SSI5 SSI4 SSI3 SSI2 SSI1 SSI0 0 0 0 0 0 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W Software Standby Release IRQ Setting These bits select the IRQn pins used to recover from the software standby state. 0: IRQn requests are not sampled in the software standby state (Initial value when n = 7 to 3). 1: When IRQn request occurs in the software standby state, the chip recovers from the software standby state after the elapse of the oscillation settling time (Initial value when n = 2 to 0). 5.4 Interrupt Sources 5.4.1 External Interrupt Sources There are nine external interrupts: NMI and IRQ7 to IRQ0. These interrupts can be used to restore the chip from software standby mode. NMI Interrupt: Nonmaskable interrupt request (NMI) is the highest-priority interrupt, and is always accepted by the CPU regardless of the interrupt control mode or the status of the CPU interrupt mask bits. The NMIEG bit in INTCR can be used to select whether an interrupt is requested at a rising edge or a falling edge on the NMI pin. IRQ7 to IRQ0 Interrupts: Interrupts IRQ7 to IRQ0 are requested by an input signal at pins IRQ7 to IRQ0. Interrupts IRQ7 to IRQ0 have the following features. • Using ISCR, it is possible to select whether an interrupt is generated by a low level, falling edge, rising edge, or both edges, at pins IRQ7 to IRQ0. • Enabling or disabling of interrupt requests IRQ7 to IRQ0 can be selected with IER. • The interrupt priority level can be set with IPR. • The status of interrupt requests IRQ7 to IRQ0 is indicated in ISR. ISR flags can be cleared to 0 by software. When IRQ7 to IRQ0 interrupt requests occur at low level of IRQn, the corresponding IRQ should be held low until an interrupt handling starts. Then the corresponding IRQ should be set to high in the interrupt handling routine and clear the IRQnF bit (n = 0 to 7) in ISR to 0. Interrupts may not be executed when the corresponding IRQ is set to high before the interrupt handling starts. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |