 |
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
|
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M16C/62 bảng dữ liệu(PDF) 148 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
M16C/62 bảng dữ liệu(HTML) 148 Page - Renesas Technology Corp |
|
|
148 / 615 page  Clock asynchronous serial I/O (UART) mode Mitsubishi microcomputers M16C / 62A Group SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER 1-129 Transmit enable bit(TE) Transmit buffer empty flag(TI) Transmit register empty flag (TXEPT) Start bit Parity bit TxDi CTSi The above timing applies to the following settings : • Parity is enabled. • One stop bit. • CTS function is selected. • Transmit interrupt cause select bit = “1”. “1” “0” “1” “L” “H” “0” “1” Tc = 16 (n + 1) / fi or 16 (n + 1) / fEXT fi : frequency of BRGi count source (f1, f8, f32) fEXT : frequency of BRGi count source (external clock) n : value set to BRGi Transmit interrupt request bit (IR) “0” “1” Cleared to “0” when interrupt request is accepted, or cleared by software Transmit enable bit(TE) Transmit buffer empty flag(TI) TxDi Transmit register empty flag (TXEPT) “0” “1” “0” “1” “0” “1” The above timing applies to the following settings : • Parity is disabled. • Two stop bits. • CTS function is disabled. • Transmit interrupt cause select bit = “0”. Transfer clock Tc Tc = 16 (n + 1) / fi or 16 (n + 1) / fEXT fi : frequency of BRGi count source (f1, f8, f32) fEXT : frequency of BRGi count source (external clock) n : value set to BRGi Transmit interrupt request bit (IR) “0” “1” Shown in ( ) are bit symbols. Shown in ( ) are bit symbols. Tc Transfer clock D0 D1 D2 D3 D4 D5 D6 D7 ST P D0 D1 D2 D3 D4 D5 D6 D7 SP ST P SP D0 D1 ST Stopped pulsing because transmit enable bit = “0” Stop bit Transferred from UARTi transmit buffer register to UARTi transmit register Start bit The transfer clock stops momentarily as CTS is “H” when the stop bit is checked. The transfer clock starts as the transfer starts immediately CTS changes to “L”. Data is set in UARTi transmit buffer register D0 D1 D2 D3 D4 D5 D6 D7 ST SP D8 D0 D1 D2 D3 D4 D5 D6 D7 ST D8 D0 D1 ST SPSP Transferred from UARTi transmit buffer register to UARTi transmit register Stop bit Stop bit Data is set in UARTi transmit buffer register. “0” SP Cleared to “0” when interrupt request is accepted, or cleared by software • Example of transmit timing when transfer data is 8 bits long (parity enabled, one stop bit) • Example of transmit timing when transfer data is 9 bits long (parity disabled, two stop bits) Figure 1.16.17. Typical transmit timings in UART mode(UART0,UART1) |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Vietnamese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
