| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PCA9527DPZ bảng dữ liệu(PDF) 8 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
PCA9527DPZ bảng dữ liệu(HTML) 8 Page - NXP Semiconductors |
|
8 / 23 page ![]() NXP Semiconductors PCA9527 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 002aad972 VCC(A) VCC(B) SDAB SDAA SCLB SCLA 2.7 kΩ 10 kΩ (optional) GND 10 kΩ CECB 3.3 V 0.1 µF 10 kΩ HDMI TRANSMITTER PCA9527 0.1 µF 1.5 kΩ to 2.0 kΩ (2×) 5 V HDMI cable DDC line LCD TV (sink) PCA9507 PCA9512A PCA9515 PCA9517 PCA9527 DVD/R or STB 22 Ω EN 10 kΩ CECA 22 Ω Figure 6. Source or DVD/R, STB application 002aad973 VCC(A) VCC(B) SDAB SDAA SCLB SCLA 10 kΩ (optional) GND 10 kΩ CECB 3.3 V 0.1 µF 10 kΩ HDMI RECEIVER PCA9527 0.1 µF 47 kΩ 5 V HDMI cable DDC line DVD (source) PCA9507 PCA9512A PCA9515 PCA9517 PCA9527 LCD TV 22 Ω 22 Ω EN 10 kΩ CECA 10 kΩ Figure 7. Sink or LCD TV application According to Figure 5, when port A of the PCA9527 is pulled LOW by a driver on the I2C- bus, a comparator detects the falling edge when it goes below 0.3VCC(A) and causes the internal driver on port B to turn on, causing port B to pull down to about 0.5 V. When port B of the PCA9527 falls, first a CMOS hysteresis type input detects the falling edge and causes the internal driver on port A to turn on and pull the port A pin down to ground. In order to illustrate what would be seen in a typical application, refer to Figure 11 and Figure 12. If the bus controller in Figure 5 were to write to the target through the PCA9527, waveforms shown in Figure 11 would be observed on the A bus. This looks like a normal I2C-bus transmission except that the HIGH level may be as low as 2.7 V, and the turn on and turn off of the acknowledge signals are slightly delayed. The controller drives the B bus to ground or lets it float to VCC(B) as it sends data to the target at the falling edge of the 8th clock, controller releases SDAB on the B bus and target pulls SDAA on the A bus to ground, causing the PCA9527 to pull SDAB on the B bus to 0.5 V. At the falling edge of the 9th clock, the controller again drives the B bus and target releases the A bus. Multiple PCA9527 port A sides can be connected in a star configuration (Figure 8), allowing all nodes to communicate with each other. Multiple PCA9527s can be connected in series (Figure 9) as long as port A is connected to port B. I2C-bus target devices can be connected to any of the bus segments. The number of devices that can be connected in series is limited by repeater delay/time-of- flight considerations on the maximum bus speed requirements. PCA9527 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2021. All rights reserved. Product data sheet Rev. 1.1 — 20 August 2021 8 / 23 |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |