| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PCA9527DPZ bảng dữ liệu(PDF) 4 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
PCA9527DPZ bảng dữ liệu(HTML) 4 Page - NXP Semiconductors |
|
4 / 23 page ![]() NXP Semiconductors PCA9527 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus Symbol Pin Description EN 6 active HIGH buffer enable input CECB 7 serial data with static level offset, powered by VCC(B), 5 V tolerant SDAB 8 serial data port B bus with static level offset, 5 V tolerant SCLB 9 serial clock port B bus with static level offset, 5 V tolerant VCC(B) 10 port B supply voltage (2.7 V to 3.6 V) Table 3. Pin description...continued 6 Functional description Refer to Figure 1. The PCA9527 consists of 3 channels of bidirectional open-drain I/Os specifically designed to support up-translation/down-translation between low voltages (as low as 2.7 V) and a 3.3 V or 5 V I2C-bus and SMBus. The device contains a rise time accelerator, specifically on port A of the SCLA and SDAA that enables the device to drive a long cable or a heavier capacitive load for DDC, I2C-bus and SMBus applications. With dual supply rails, the device translates from voltage ranges 2.7 V to 5.5 V down to a voltage as low as 2.7 V without degradation of system performance. Unlike the SDAA and SCLA, the CECA is powered by the VCC(B) and does not have a rise time accelerator, but is similar in that its port A has normal I/O and port B static level offset. All I/Os are overvoltage tolerant to 5.5 V even when the device is un-powered (VCC(B) and/or VCC(A) = 0 V). The PCA9527 includes a power-up circuit that keeps the SDA and SCL output drivers turned off until VCC(A) and VCC(B) rise above 2.7 V. The CECA output drivers are turned OFF until VCC(B) rises above 2.7 V. VCC(A) and VCC(B) can be applied in any sequence at power-up. 002aad435 0.3VCC(B) 0.4 V port B VCC(B) port A VCC(A) 0.3VCC(A) 0.5 V 0.7VCC(A) 0 V 0 V Figure 3. Port A and port B I/O levels When port B falls first and goes below 0.3VCC(B) the port A driver is turned on and port A pulls down to 0 V. As port A falls below 0.3VCC(A) the port B pulls down to about 0.5 V. The external port B driver must drive the port B to a LOW that is ≤ 0.4 V or else it is not possible to know who is driving the port A LOW. The PCA9527 direction control assumes that port A is controlling the part unless port B falls below 0.4 V. When the port B voltage is ≤ 0.4 V the port A driver of the PCA9527 is on and holds port A down to nearly 0 V. As the port B voltage rises because the external driver turns off, the port B voltage rises up to ~0.5 V because port A is LOW; once port B rises to ~0.5 V the port A pull-down driver turns off. Then port A rises with a rise time determined by the RC of port A when it crosses the port A threshold ~0.3VCC(A) the port B driver is turned off and the rising edge accelerator is turned on, which causes a faster rising edge until it reaches the turn-off PCA9527 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2021. All rights reserved. Product data sheet Rev. 1.1 — 20 August 2021 4 / 23 |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |