| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
THAT2252 bảng dữ liệu(PDF) 6 Page - THAT Corporation All rights reserved. |
|
|
|||||||||||||||||||||||||||||
THAT2252 bảng dữ liệu(HTML) 6 Page - THAT Corporation All rights reserved. |
|
6 / 10 page ![]() production of positive-half input signals. The base of Q2 is brought out to pin 4 in order to allow ad- justment for mismatches between these transis- tors and for the input offset voltage of OA1. Pin 4 should be connected to a variable low-impedance voltage source capable of supplying a few millivolts (VSYM). The base of Q1 is connected to its collector through a 20 Ω resistor to allow matching between the base impedances of Q1 and Q2. A 20 Ω source should be used at pin 4 for optimum matching. Input Bias Currents and Voltages OA1 will rectify any currents flowing in its feed- back network, including the bias current of OA1 it- self. Input signals below OA1’s bias current will be obscured, with a steady dc output “floor” the re- sult. The input bias compensation for OA1 largely cancels OA1’s bias current, improving low-level performance. Even if overcompensated, any uncor- rected bias current (positive or negative) in OA1 results in a limit to the low-level resolution of the 2252. Any dc offset voltage at pin 1 will cause dc input currents to flow if the input is dc coupled. The dc offset at pin 1 is typically 8 mV, so the input should be ac coupled (as shown in Figure 4) for most applications. If low-level performance is not required, dc coupling may be used without further modifications to the application circuits. However, dc coupling and good low-level performance are possible with additional external circuitry, as de- scribed in the section on DC Measurements on Page 9. Positive equivalent input bias current in OA2 (after correction) will also add to the output level read- ing. This is because the equivalent input bias cur- rent is supplied through Q4 and Q5, which adds to the dc level at the output of OA2. OA2, like OA1, has input bias compensation. While generally ex- tending low-level performance, the compensation can cause OA2’s net input bias requirement to be- come negative, tending to reverse bias Q4 and Q5. The circuit of Figure 4 uses a 22 M Ω resistor, Rf, to supply increasing dc input current as the 2252 output drops. This forces current to flow in Q2, which overwhelms any negative input bias at OA2 and prevents the current in Q4 and Q5 from re- versing. Rf is responsible for the flattening of the low-level response shown in Figure 6 (Page 5). The feed- back current provided enforces a lower limit to the resolvable input current. Without this feedback, those 2252s where the OA2 input bias is overcorrected will exhibit a sharp downward swing in output level at low input signals (see Figure 8). For many applications, such low-level response is not necessary. In such cases, Rf may be deleted, as shown in Figure 11. See further discussion of this subject in Output Considerations, (Page 8). Applications The intended purpose of the 2252 is to compute the log of the time-weighted root-mean-square of an input current signal. Several practical consider- ations apply when attempting to make full use of the 100 dB dynamic range of the device. Input Considerations The 2252 input is intended to accept a current: as is clear from Figure 3 (page 3), pin 1 is a summing junction supplied with internal negative feedback. Maximum input current is on the order of 1 mA, limited by internal device characteristics. The min- imum practical input current is determined by the effects of internal bias currents (whether from OA1, OA2, or the effect of V1). At currents as low as 31 nA, approximately 1 dB error in reading will result from interal bias currents. THAT Corporation; 45 Sumner Street; Milford, Massachusetts 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Page 6 THAT 2252 RMS-Level Detector Figure 8. Low Level Output from Several 2252s (no Rf) V+ OUT IN 7 2 6 3 8 1 5 4 2252 V+ OUT CAP V- SYM GND IBIAS IN V- V- T C RT 20 22M Rf 1k 2M2 750k 1u Rb 10u 20u Cin 10u 10k Rin Figure 9. Application Circuit Without Symmetry Control |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |