| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
THAT2252 bảng dữ liệu(PDF) 5 Page - THAT Corporation All rights reserved. |
|
|
|||||||||||||||||||||||||||||
THAT2252 bảng dữ liệu(HTML) 5 Page - THAT Corporation All rights reserved. |
|
5 / 10 page ![]() given input frequency, fin. Larger values of τ re- duce ripple at the expense of longer attack and re- lease times. For fin >> 1 4 p t , the ripple voltage at the output is given by: VR V f T in » 4 2 p t , where VR is the rms ripple voltage. Taking the Square Root The square root portion of the Root-Mean Square is implied by the constant of proportionality for the output voltage: it is not computed explicitly. This is because, in the log representation, taking the square root is equivalent to division by two. The voltage at pin 6 is proportional to the mean of the square at approximately 3 mV/dB, and propor- tional to the square root of the mean of the square at approximately 6 mV/dB. Output Buffering and Level Shifting The voltage at pin 6 is buffered by OA3, and level shifted down by the bias voltage V3. Level shifting is required so that the output voltage will be zero when the rms input current reaches a predeter- mined value, Iin0. This current is often called level match, and represents the 0 dB reference of the circuit. The various level shifts throughout the 2252 are as follows: V2 represents one diode drop, so the volt- age at the emitter of Q4 is +1VBE. The output of OA2 is two diode drops higher than this, or +3VBE. Q6 will subtract one diode drop from the output of OA2, so the voltage at pin 6 will be +2VBE. Finally, V3 represents two diode drops, setting the voltage at pin 7 to 0 V. Of course, the actual value of all these level shifts is dependent on the currents through the transis- tors responsible for each VBE. These currents, in turn, are dependent on the bias programming cur- rent in pin 2 (IBIAS) and the timing current pulled from pin 6 (IT). This dependence may be given as follows: Iin I I BIAS T 0 2 9 = . , where Iin0 is the input current causing 0 V output, IT is the current in pin 6, and IBIAS is the current in pin 2. The factor 2.9 derives from the geometry of the transistors involved. Figure 6 plots output voltage versus input level for a 2252 in its recommended circuit configuration (Figure 4). In this plot, 0 dBr ≈ 43 mV. Figure 7 plots output voltage for several different con- stant-amplitude frequency sweeps for the same cir- cuit. The vertical divisions are 60 mV apart, representing approximately 10 dB increments. Full audio bandwidth is maintained over a 60 dB dy- namic range. Current Programming All the internal current sources in the 2252 are slaved to the current in pin 2, IBIAS. As mentioned above, the choice of this current affects Iin0. IBIAS is normally set by a resistor from pin 2 to ground (VCC would do also). Note that the voltage at pin 2 is normally VEE + 2.1 V, where VEE is the negative supply voltage. Symmetry Adjustment The rectifier (Q1 through Q3 and OA1) depends on the matching between Q1 and Q2 for accurate re- THAT Corporation; 45 Sumner Street; Milford, Massachusetts 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com 600032 Rev 02 Page 5 Figure 6. 2252 DC Output Vs. AC Input Level Figure 7. 2252 DC Output Vs. Frequency at Various Levels Figure 5. Tone Burst Response |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |