| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ADSP-21990BBC bảng dữ liệu(PDF) 40 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADSP-21990BBC bảng dữ liệu(HTML) 40 Page - Analog Devices |
|
40 / 50 page ![]() Rev. A | Page 40 of 50 | August 2007 ADSP-21990 POWER DISSIPATION Total power dissipation has two components, one due to inter- nal circuitry and one due to the switching of external output drivers. Internal power dissipation is dependent on the instruc- tion execution sequence and the data operands involved. The external component of total power dissipation is caused by the switching of output pins. Its magnitude depends on: • Number of output pins that switch during each cycle (O) • The maximum frequency at which they can switch (f) • Their load capacitance (C) • Their voltage swing (VDD) and is calculated by the formula below. The load capacitance includes the processor package capaci- tance (CIN). The switching frequency includes driving the load high and then back low. Address and data pins can drive high and low at a maximum rate of 1/(2tCK). The write strobe can switch every cycle at a frequency of 1/tCK. Select pins switch at 1/(2tCK), but selects can switch on each cycle. For example, esti- mate PEXT with the following assumptions: • A system with one bank of external data memory—asyn- chronous RAM (16-bit) •One 64K 16 RAM chip is used with a load of 10 pF • Maximum peripheral speed CCLK = 80 MHz, HCLK = 80 MHz • External data memory writes occur every other cycle, a rate of 1/(4tHCLK), with 50% of the pins switching • The bus cycle time is 80 MHz (tHCLK = 12.5 ns) The PEXT equation is calculated for each class of pins that can drive as shown in Table 16. A typical power consumption can now be calculated for these conditions by adding a typical internal power dissipation with the following formula. Where: • PEXT is from Table 16. • PINT is IDDINT 2.5 V, using the calculation IDDINT listed in Power Dissipation. Note that the conditions causing a worst-case PEXT are different from those causing a worst-case PINT. Maximum PINT cannot occur while 100% of the output pins are switching from all ones to all zeros. Note also that it is not common for an application to have 100% or even 50% of the outputs switching simultaneously. P EXT OC × V DD 2 × f × = P TOTAL P = EXT P INT + Table 16. PEXT Calculation Example Pin Type Number of Pins % Switching C f VDD 2 = PEXT Address 15 50 10 pF 20 MHz 10.9 V = 0.01635 W MSx 1 0 10 pF 20 MHz 10.9 V = 0.0 W WR 1 10 pF 40 MHz 10.9 V = 0.00436 W Data 16 50 10 pF 20 MHz 10.9 V = 0.01744 W CLKOUT 1 10 pF 80 MHz 10.9 V = 0.00872 W = 0.04687 W |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |