| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DIO5090C bảng dữ liệu(PDF) 13 Page - DIOO MICROCIRCUITS CO., LTD |
|
|
|||||||||||||||||||||||||||||
DIO5090C bảng dữ liệu(HTML) 13 Page - DIOO MICROCIRCUITS CO., LTD |
|
13 / 20 page ![]() DIO5090C www.dioo.com © 2021 DIOO MICROCIRCUITS CO., LTD DIO5090C • Rev.1.1 - 13 - The constant charge timer is fixed at 10 hours and can be increased real time by going into thermal regulation, IN- DPM or if in USB current limit. The timer clock slows by a factor of 2, resulting in a clock than counts half as fast when in these modes. If either the 30 minute or ten hour timer times out, the charging is terminated and the /CHG terminal goes high impedance if not already in that state. The timer is reset by disabling the IC, cycling power or going into and out of TTDM. Termination Once the BAT terminal goes above VRCH, (reaches voltage regulation) and the current tapers down to the termination threshold, the /CHG terminal goes high impedance. If the battery is present, the charge current will terminate. If the battery was removed along with the thermistor, then the TS terminal is driven high and the charge enters TTDM. Refresh Threshold After termination, if the BAT terminal voltage drops to VRCH (150mV below regulation) then a new charge is initiated, but the /CHG terminal remains at a high impedance (off). Application Information The DIO5090C series of devices are highly integrated Li-Ion and Li-Pol linear chargers devices targeted at space- limited portable applications. The devices operate from either a USB port or AC adapter. The high input voltage range with input overvoltage protection supports low-cost unregulated adapters. These devices have a single power output that charges the battery. A system load can be placed in parallel with the battery as long as the average system load does not keep the battery from charging fully during the 10 hours safety timer. Typical Applications IBAT_CONSTANT_CHG = 500mA; IBAT_TRICKLE_CHG = 100mA; IBAT_TERM = 50mA Figure 3. Typical Applications for DIO5090C 1.5kΩ Adaptor IN ETERM ISET2 Disconnect after Detection System Load DC+ GND 1 BAT 10 1.5kΩ Battery Pack 2 ISET TS 9 OR USB Port + 1μF /CHG 8 3 VSS 1μF 910Ω 1.6kΩ 4 PR 7 5 /PG NC 6 VDD TTDM ISET/100/500mA GND D+ D- Host VBUS GND D+ D- |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |