| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TCAN337/G bảng dữ liệu(PDF) 29 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TCAN337/G bảng dữ liệu(HTML) 29 Page - Texas Instruments |
|
29 / 47 page ![]() 7.3.2 Differential Signal CAN is a differential bus where complementary signals are sent over two wires and the voltage difference between the two wires defines the logical state of the bus. The differential CAN receiver monitors this voltage difference and outputs the bus state with a single ended logic level output signal. 75 % SAMPLE POINT 500 mV Threshold 900 mV Threshold NOISE MARGIN NOISE MARGIN RECEIVER DETECTION WINDOW Figure 7-6. Typical Differential Output Waveform The CAN driver creates the differential voltage between CANH and CANL in the dominant state. The dominant differential output of the TCAN33x is greater than 1.5V and less than 3V across a 60Ω load as defined by the ISO11898 standard. These are the same limiting values for 5V supplied CAN transceivers. The bus termination resistors drive the recessive bus state and not the CAN driver. A CAN receiver is required to output a recessive state when less than 500 mV of differential voltage exists on the bus, and a dominant state when more than 900mV of differential voltage exists on the bus. The CAN receiver must do this with common-mode input voltages from –2V to 7V. The TCAN33x family receivers meet these same input specifications as 5V supplied receivers. 7.3.3 Common-Mode Signal and EMC Performance A common-mode signal is an average voltage of the two signal wires that the differential receiver rejects. The common-mode signal comes from the CAN driver, ground noise, and coupled bus noise. Since the bias voltage of the recessive state of the device is dependent on VCC, any noise present or variation of VCC has an effect on this bias voltage seen by the bus. The TCAN33x family has the recessive bias voltage set higher than 0.5 x VCC to match common mode in recessive mode to dominant mode. This results in superior EMC performance. 7.4 Power Supply Recommendations For reliable operation at all data rates and supply voltages, each supply should be decoupled with a 100nF ceramic capacitor located as close to the VCC supply pins as possible. The TPS76333 is a linear voltage regulator suitable for the 3.3V supply. 7.5 Layout 7.5.1 Layout Guidelines TCAN33x family of devices incorporates integrated IEC 61000-4-2 ESD protection. Should the system requires additional protection against ESD, EFT or surge, additional external protection and filtering circuitry may be needed. In order for the PCB design to be successful, start with design of the protection and filtering circuitry. Because ESD and EFT transients have a wide frequency bandwidth from approximately 3MHz to 3GHz, high frequency layout techniques must be applied during PCB design. www.ti.com TCAN330, TCAN332, TCAN334, TCAN337 TCAN330G, TCAN332G, TCAN334G, TCAN337G SLLSEQ7F – DECEMBER 2015 – REVISED MAY 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 29 Product Folder Links: TCAN330 TCAN332 TCAN334 TCAN337 TCAN330G TCAN332G TCAN334G TCAN337G |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |