CC2640R2FYFVT.B datasheet(20/74 Pages) TI2

20 / 74 page

Measured on the TI CC2650EM-5XD reference design with Tc = 25°C, VDDS = 3.0 V, fRF = 2440 MHz, unless

otherwise noted.

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

Selectivity, image frequency

±1 MHz(1)

Note that Image frequency + 1 MHz is the Co-channel

–1 MHz. Wanted signal at –79 dBm, modulated

interferer at ±1 MHz from image frequency, BER =

10–3

5 / 32(2)

Blocker rejection, ±8 MHz and

above(1)

Wanted signal at –79 dBm, modulated interferer at ±8

MHz and above, BER = 10–3

>46

Out-of-band blocking (3)

30 MHz to 2000 MHz

–40

dBm

Out-of-band blocking

2003 MHz to 2399 MHz

–19

dBm

Out-of-band blocking

2484 MHz to 2997 MHz

–22

dBm

Intermodulation

Wanted signal at 2402 MHz, –76 dBm. Two

interferers at 2405 and 2408 MHz respectively, at the

given power level

–42

dBm

(1)

Numbers given as I/C dB.

(2)

X / Y, where X is +N MHz and Y is –N MHz.

(3)

Excluding one exception at Fwanted / 2, per Bluetooth Specification.

8.7 125-kbps Coded (Bluetooth 5) – TX

Measured on the TI CC2650EM-5XD reference design with Tc = 25°C, VDDS = 3.0 V, fRF = 2440 MHz, unless

otherwise noted.

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

Output power, highest setting

Differential mode, delivered to a single-ended 50-Ω load

through a balun

dBm

Output power, highest setting

Measured on CC2650EM-4XS, delivered to a single-ended

50-Ω load

dBm

Output power, lowest setting

Delivered to a single-ended 50-Ω load through a balun

–21

dBm

Spurious emission conducted

measurement(1)

f < 1 GHz, outside restricted bands

–43

dBm

f < 1 GHz, restricted bands ETSI

–65

dBm

f < 1 GHz, restricted bands FCC

–71

dBm

f > 1 GHz, including harmonics

–46

dBm

(1)

Suitable for systems targeting compliance with worldwide radio-frequency regulations ETSI EN 300 328 and EN 300 440 Class 2

(Europe), FCC CFR47 Part 15 (US), and ARIB STD-T66 (Japan).

8.8 500-kbps Coded (Bluetooth 5) – RX

Measured on the TI CC2650EM-5XD reference design with Tc = 25°C, VDDS = 3.0 V, fRF = 2440 MHz, unless

otherwise noted.

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

Receiver sensitivity

Differential mode. Measured at the CC2650EM-5XD

SMA connector, BER = 10–3

–101

dBm

Receiver saturation

Differential mode. Measured at the CC2650EM-5XD

SMA connector, BER = 10–3

dBm

Frequency error tolerance

Difference between the incoming carrier frequency

and the internally generated carrier frequency

–240

240

kHz

Data rate error tolerance

Difference between incoming data rate and the

internally generated data rate (37-byte packets)

–500

500

ppm

Data rate error tolerance

Difference between incoming data rate and the

internally generated data rate (255-byte packets)

–310

330

ppm

Co-channel rejection (1)

Wanted signal at –72 dBm, modulated interferer in

channel, BER = 10–3

–5

Selectivity, ±1 MHz (1)

Wanted signal at –72 dBm, modulated interferer at ±1

MHz, BER = 10–3

9 / 5(2)

CC2640R2F

SWRS204C – DECEMBER 2016 – REVISED SEPTEMBER 2020

www.ti.com

Submit Document Feedback

Product Folder Links: CC2640R2F

CC2640R2FYFVT.B bảng dữ liệu(PDF) 20 Page - Texas Instruments

CC2640R2FYFVT.B bảng dữ liệu(HTML) 20 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74

bảng dữ liệu tải về

Link URL