TMP91CW60DFG datasheet(11/262 Pages) TOSHIBA

11 / 262 page

Page 8

2007-12-03

TMP91CW60

Note: All pins that have built-in pull-up resistors (other than the RESET pin) can be disconnected from the built-in pull-up

resistor by software.

P95

SCLK1

CTS1

Port 95: I/O port

Serial Clock I/O 1

Serial Data Send Enable 1 (Clear to Send)

P96

XT1

Port 96: I/O port

Low-frequency oscillator connection pin

P97

XT2

Port 97: I/O port

Low-frequency oscillator connection pin

PA0

TB2IN0

INT1

Port A0: I/O port

16-bit timer 2 input 0:Timer B2 count/capture trigger Input 0

Interrupt Request Pin 1: Interrupt request pin with programmable rising edge / falling edge.

PA1

TB2IN1

INT2

Port A1: I/O port

16-bit timer 2 input 1:Timer B2 count/capture trigger Input 1

Interrupt Request Pin 2: Interrupt request on rising edge

PA2

TB2OUT0

Port A2: I/O port

16-bit timer 2 output 0: Timer B2 Output 0

PA3

TB2OUT1

Port A3: I/O port

16-bit timer 2 output 1: Timer B2 Output 1

PB0

TB4IN0

INT9

SDA1

Port B0: I/O port

16-bit timer 4 input 0:Timer B4 count/capture trigger Input 0

Interrupt Request Pin 9: Interrupt request pin with programmable rising edge / falling edge.

Serial bus interface data 1 in I2C bus Mode.

PB1

TB4IN1

INT10

SCL1

Port B1: I/O port

16-bit timer 4 input 1:Timer B4 count/capture trigger Input 1

Interrupt Request Pin 10: Interrupt request on rising edge

Serial bus interface clock 1 in I2C bus Mode.

PB2

TB4OUT0

Port B2: I/O port

16-bit timer 4 output 0: Timer B4 Output 0

PB3

TB4OUT1

Port B3: I/O port

16-bit timer 4 output 1: Timer B4 Output 1

NMI

Non-Maskable Interrupt Request Pin: Interrupt request pin with programmable falling edge or both

edge.

AM0-1

Operation mode:Fixed to AM1 "1", AM0 "1".

EMU0-1

Set to Open pins

RESET

Reset: initializes TMP91CW60. (with pull-up resistor)

VREFH

Pin for reference voltage input to AD converter

AVCC

Power supply pin for AD converter

AVSS

GND pin for AD converter (0 V)

X1/X2

High frequency oscillator connection pins

DVCC

Power supply pins (All DVCC pins should be connected with the power supply pin.)

DVSS

GND pins (0 V) (All DVSS pins should be connected with the GND (0V) pin.)

Table 1-1

Pin Names and Functions(3/3)

Name

Number

Input

Output

Functions

TMP91CW60DFG bảng dữ liệu(PDF) 11 Page - Toshiba Semiconductor

TMP91CW60DFG bảng dữ liệu(HTML) 11 Page - Toshiba Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL