công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

HMC8364LP6GETR bảng dữ liệu(PDF) 16 Page - Analog Devices

tên linh kiện HMC8364LP6GETR
Giải thích chi tiết về linh kiện  18.10 GHz to 26.60 GHz Quadband VCO
PDF  17 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  AD [Analog Devices]
Trang chủ  http://www.analog.com
Logo AD - Analog Devices

HMC8364LP6GETR bảng dữ liệu(HTML) 16 Page - Analog Devices

Back Button HMC8364LP6GETR Datasheet HTML 9Page - Analog Devices HMC8364LP6GETR Datasheet HTML 10Page - Analog Devices HMC8364LP6GETR Datasheet HTML 11Page - Analog Devices HMC8364LP6GETR Datasheet HTML 12Page - Analog Devices HMC8364LP6GETR Datasheet HTML 13Page - Analog Devices HMC8364LP6GETR Datasheet HTML 14Page - Analog Devices HMC8364LP6GETR Datasheet HTML 15Page - Analog Devices HMC8364LP6GETR Datasheet HTML 16Page - Analog Devices HMC8364LP6GETR Datasheet HTML 17Page - Analog Devices  
Zoom Inzoom in Zoom Outzoom out
 16 / 17 page
background image
HMC8364
Data Sheet
Rev. A | Page 16 of 17
APPLICATIONS INFORMATION
The HMC8364 serves as the local oscillator (LO) in microwave
synthesizer applications. The primary applications for this
device are point to point and multipoint radios, military radars,
test and measurement, industrial and medical equipment, and
wireless communication infrastructure. The low phase noise
allows higher orders of modulation and offers improved bit
error rates in communication systems. Stable loop filter design
is easily achieved due to the linear, monotonic tuning sensitivity
across the four-VCO core, and higher output power minimizes
the gain required to drive subsequent stages. The cascode
output buffer amplifier stage guarantees stability over a wide
range of output load conditions and improves the pulling
performance of the VCO cores.
To achieve optimal performance of the VCO cores, including
the lowest phase noise native to VCOs, use high power supply
rejection ratio (PSRR) and low dropout (LDO) regulators to
minimize any spurious frequencies from the power supply. The
ADM7150 and the LT3042 meet these requirements and are
acceptable LDO regulators to use.
The wide frequency range of the VCO cores suggests the use of
a low noise, PLL synthesizer, such as the ADF41513. The wide
input bandwidth of the ADF41513 (1 GHz to 26.5 GHz) makes
it an ideal synthesizer to be used with the HMC8362. The charge
pump current can be varied up or down on the ADF41513 to
compensate for VCO sensitivity variation. Many applications
require actively switching between the four VCO cores as
quickly as possible. Enabling more than one VCO core at a
time is not recommended. Therefore, use of an appropriate
4:1 multiplexer such as the ADG1604 is recommended. The
ADG1604 has low on resistance, the ability to operate with
either 3 V or 5 V logic, and offers break before make switch
sequencing. Alternatively, multiple ADG854 switches can also
be used to enable and disable the VCO cores. Although this
switch also includes a break before make delay, users must
prevent the possibility of powering up more than one VCO
core at a time. Regardless of which approach is used to control
the VCO cores, an additional ADG854 can be used to control
bias to the upper portion of the cascode amplifier circuitry for
use in muting the RF output (RFOUT, Pin 5) if desired. Muting
RFOUT suppresses the output power by approximately 20 dB
across all cores) and does not impact long-term reliability when
only one VCO core is powered up at a time.
It is important to follow optimal RF layout practices for the
layout of the interconnecting circuit. Give first priority to the
microwave power splitter network from the output buffer of
the VCO cores to the RF input pin (RFINA) of the ADF41513.
Give the next highest priority to the highly sensitive VTUNE line
with the first pole placed as close to the ADF41513 CP output
pin as possible, and the final RC pole of the filter placed as close
to the HMC8364 VTUNE pin as possible. The wide tuning range
of the HMC8364 requires the use of a high voltage, low noise,
operational amplifier. The ADA4625-1 is acceptable to use for
such applications.
The suggested PCB stackup consists of a high quality dielectric
material, such as Rogers 4003. The transmission lines carrying
the high frequency signal must be carefully controlled with
50 Ω characteristic impedances.
RFOUT
EN
A0
A1
S3
S4
S2
S1
VC1
VTUNE
VC2
VC3
VC4
VCB
D1
VDD
S1B
IN1
S1A
RF OUT
VTUNE
HMC8364
ADG854
ADG1604
TO DIGITAL
CONTROL PINS
ADF41513
PLL
SYNTHESIZER
LOOP FILTER
CIRCUIT
REFERENCE
INPUT
5V VCC
5V VCC
D
REFIN
RFINA
CP
POWER SPLITTER
NETWORK
NOTES
1. THIS IS A SIMPLIFIED SCHEMATIC OF A TYPICAL APPLICATION DIAGRAM. PASSIVE COMPONENTS DETAILS HAVE BEEN OMITTED FOR CLARITY.
Figure 43. Typical Application Diagram



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com