| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TPS2340APFPR bảng dữ liệu(PDF) 13 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TPS2340APFPR bảng dữ liệu(HTML) 13 Page - Texas Instruments |
|
13 / 27 page ![]() TPS2340A SLUS528A – MARCH 2002 – REVISED AUGUST 2002 13 www.ti.com APPLICATION INFORMATION fault handling When PGOOD is asserted (main power is valid), the serial interface is available for use. At this time, Auxflt and Faultx (i.e. Faultx = Pwrfltx • Auxflt) signals are present in the registers and can be read back over the serial interface. When PGOOD is deasserted (main power is not valid), the serial interface is inactive, so the TPS2340A provides an alternate path for observing the Auxfltx signals. In this case, Auxfltx is presented on the ATTLEDx open-drain output, so 3Vaux faults can be observed. Systems that do not require Auxfltx indications when main power is off should use main power to supply current to the attention LEDs. In addition, when TEST is asserted after PGOOD has changed from 0 to 1, the AND of Pwrfltx and Auxfltx is present on the ATTLEDx open-drain output, so the attention LEDs can be used to report any faults on each channel. After PGOOD is asserted with TEST deasserted and the voltage on the SWx pin is greater than VDIGVCC but less than VV5IN, ATTLEDx follows the fault status of the main power fault (Pwrfltx). If the SWx input is pulled to VV5IN potential, that slot becomes immediately enabled independent of serial interface status and ATTLEDx follows the fault status of the main power fault (Pwrfltx). Table 1. Fault Reporting Using ATTLED SWx PGOOD TEST ATTLEDx < VDIGVCC 0 x Auxfltx < VDIGVCC 1 1 Pwrfltx • Auxfltx > VDIGVCC, < VV5IN 1 0 Pwrfltx = VV5IN x x Pwrfltx PCI–XCAP resolution Add-in cards indicate their PCI-X mode and frequency capabilities by connection of the PCI-XCAP pin. The TPS2340A utilizes a three-level comparator to resolve the PCI-XCAP input so as to decode operating mode and generate the PCI-XCAP2 and PCI-XCAP1 internal signals. With PCI-XCAP open, the TPS2340A selects PCI-X 133-MHz operation. PCI-X 66-MHz operation is selected by a 10-k Ω pull-down resistor on PCI-XCAP. With PCI-XCAP grounded, conventional PCI-2.2 operation is selected. This decoding conforms to the standard PCI-X specification for PCI-XCAP resolution. Table 2. PCI-XCAP Pin State Resolution PCI-XCAP PCI-XCAP2 PCI-XCAP1 DESCRIPTION GND 0 0 Conventional PCI 2.2 operation 10-k Ω Pull-down Resistor 0 1 PCI-X 66-MHz operation Open Circuit 1 1 PCI-X 133-MHz operation |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |