| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
CS5461A bảng dữ liệu(PDF) 25 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS5461A bảng dữ liệu(HTML) 25 Page - Cirrus Logic |
|
25 / 41 page ![]() CS5461A DS661F1 25 6. REGISTER DESCRIPTION 1. “Default” => bit status after power-on or reset 2. Any bit not labeled is Reserved. A zero should always be used when writing to one of these bits. 6.1 Configuration Register Address: 0 Default = 0x000001 PC[6:0] Phase compensation. A 2’s complement number which sets a delay in the voltage channel rel- ative to the current channel. When MCLK = 4.096 MHz and K = 1, the phase adjustment range is approximately ±2.8 degrees with each step approximately 0.04 degrees (assuming a power line frequency of 60 Hz). If (MCLK/K) is not 4.096 MHz, the values for the range and step size should be scaled by the factor 4.096 MHz / (MCLK/K). Default setting is 0000000 = 0.0215 de- gree phase delay at 60 Hz (when MCLK = 4.096 MHz). Igain Sets the gain of the current PGA. 0 = Gain is 10x (default) 1 = Gain is 50x EWA Allows the E1 and E2 pins to be configured as open-collector output pins. 0 = Normal outputs (default) 1 = Only the pull-down device of the E1 and E2 pins are active IMODE, IINV Interrupt configuration bits. Select the desired pin behavior for indication of an interrupt. 00 = Active-low level (default) 01 = Active-high level 10 = High-to-low pulse 11 = Low-to-high pulse EPP Allows the E1 and E2 pins to be controlled by the EOP and EDP bits. 0 = Normal operation of the E1 and E2 pins. (default) 1 = EOP and EDP bits defines the E1 and E2 pins. EOP EOP defines the value of the E1 pin when EPP = 1. 0 = Logic level low (default) EDP EDP defines the value of the E2 pin when EPP = 1. 0 = Logic level low (default) ALT Alternate pulse format, E1 and E2 becomes active low alternating pulses with an output fre- quency proportional to the active power. 0 = Normal (default), Mechanical Counter or Stepper Motor Format 1 = Alternate Pulse Format, also MECH = 1 VHPF (IHPF) Enables the high-pass filter on the voltage (current) channel. 0 = High-pass filter disabled (default) 1 = High-pass filter enabled 23 22 21 20 19 18 17 16 PC6 PC5 PC4 PC3 PC2 PC1 PC0 Igain 15 14 13 12 11 10 9 8 EWA IMODE IINV EPP EOP EDP 7 654 32 10 ALT VHPF IHPF iCPU K3 K2 K1 K0 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |