| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
CS5461A bảng dữ liệu(PDF) 20 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS5461A bảng dữ liệu(HTML) 20 Page - Cirrus Logic |
|
20 / 41 page ![]() CS5461A 20 DS661F1 adding 2.737649x10-4 to the Temperature Offset Regis- ter (Toff). Therefore, if Toff = -0.09104831 and ∆T = -7.0 (oC), then or 0xF419BC (2’s compliment notation) is stored in the Temperature Offset Register (Toff). To convert the Temperature Register (T) from a Celsius scale (oC) to a Fahrenheit scale (oF) utilize the formula Applying the above relationship to the CS5461A tem- perature measurement algorithm If Toff = -0.09296466 and Tgain = 23.799 for a Celsius scale, then the modified values are Toff = -0.08809772 (0xF4B937) and Tgain = 42.8382 (0x55AD29) for a Fahrenheit scale. 5.7 Voltage Reference The CS5461A is specified for operation with a +2.5 V reference between the VREFIN and AGND pins. To uti- lize the on-chip 2.5 V reference, connect the VREFOUT pin to the VREFIN pin of the device. The VREFIN pin can be used to connect external filtering and/or refer- ences. 5.8 System Initialization Upon powering up, the digital circuitry is held in reset until the analog voltage reaches 4.0 V. At that time, an eight-XIN-clock-period delay is enabled to allow the os- cillator to stabilize. The CS5461A will then initialize. A hardware reset is initiated when the RESET pin is as- serted with a minimum pulse width of 50 ns. The RESET signal is asynchronous, with a Schmitt-trigger input. Once the RESET pin is de-asserted, an eight-XIN-clock-period delay is enabled. A software reset is initiated by writing the command of 0x80. After a hardware or software reset, the internal registers (some of which drive output pins) will be reset to their default values. Status bit DRDY in the Status Register, indicates the CS5461A is in its active state and ready to receive commands. 5.9 Power-down States The CS5461A has two power-down states, stand-by and sleep. In the stand-by state all circuitry except the voltage reference and crystal oscillator is turned off. To return the device to the active state a power-up com- mand is sent to the device. In sleep state all circuitry except the instruction decoder is turned off. When the power-up command is sent to the device, a system initialization is performed (see Section 5.8 System Initialization on page 20). 5.10 Oscillator Characteristics The XIN and XOUT pins are the input and output of an inverting amplifier configured as an on-chip oscillator, as shown in Figure 8. The oscillator circuit is designed to work with a quartz crystal. To reduce circuit cost, two load capacitors C1 and C2 are integrated in the device, from XIN to DGND, and XOUT to DGND. PCB trace lengths should be minimized to reduce stray capaci- tance. To drive the device from an external clock source, XOUT should be left unconnected while XIN is driven by the external circuitry. There is an amplifier be- tween XIN and the digital section which provides CMOS-level signals. This amplifier works with sinusoi- dal inputs so there are no problems with slow edge times. The CS5461A can be driven by an external oscillator ranging from 2.5 to 20 MHz, but the K divider value must be set such that the internal MCLK will run somewhere between 2.5 MHz and 5 MHz. The K divider value is set with the K[3:0] bits in the Configuration Register. As an example, if XIN = MCLK = 15 MHz, and K is set to 5, then DCLK is 3 MHz, which is a valid value for DCLK. Toff Toff T ∆ ( + 2.737649 10 4 – ) ⋅ × = Toff 0.09104831 7.0 – ( + 2.737649 10 4 – ) ⋅ × – 0.09296466 – == F o 9 5 --- C o 17.7778 + () = TF o 〈〉 9 5 --- T × gain () TC o 〈〉 Toff 17.7778 2.737649 10 4 – ⋅ × () + () + [] = Oscillator Circuit DGND XIN XOUT C1 C1 = 22 pF C2 C2 = Figure 8. Oscillator Connection |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |