TUSB8044AI datasheet(5/63 Pages) TI1

5 / 63 page

TUSB8044A

www.ti.com

SLLSF92 – FEBRUARY 2019

Product Folder Links: TUSB8044A

Submit Documentation Feedback

Pin Functions (continued)

I/O

DESCRIPTION

NAME

NO.

USB_SSRXM_UP

USB SuperSpeed receiver differential pair (negative)

USB_DP_UP

I/O

USB High-speed differential transceiver (positive)

USB_DM_UP

I/O

USB High-speed differential transceiver (negative)

USB_R1

Precision resistor reference. A 9.53-k

Ω ±1% resistor should be connected between USB_R1

and GND.

USB_VBUS

USB upstream port power monitor. The VBUS detection requires a voltage divider. The signal

USB_VBUS must be connected to VBUS through a 90.9-K

Ω ±1% resistor, and to ground

through a 10-k

Ω ±1% resistor from the signal to ground.

USB Downstream Signals

USB_SSTXP_DN1

USB SuperSpeed transmitter differential pair (positive)

USB_SSTXM_DN1

USB SuperSpeed transmitter differential pair (negative)

USB_SSRXP_DN1

USB SuperSpeed receiver differential pair (positive)

USB_SSRXM_DN1

USB SuperSpeed receiver differential pair (negative)

USB_DP_DN1

I/O

USB High-speed differential transceiver (positive)

USB_DM_DN1

I/O

USB High-speed differential transceiver (negative)

PWRCTL1/BATEN1

I/O, PD

USB Port 1 Power On Control for Downstream Power/Battery Charging Enable. The pin is

used for control of the downstream power switch for Port 1. This pin be left unconnected if

power management is not implemented.

In addition, the value of the pin is sampled at the de-assertion of reset to determine the value

of the battery charging support for Port 1 as indicated in the Battery Charging Support

0 = Battery charging not supported

1 = Battery charging supported

OVERCUR1z

I, PU

USB Port 1 Over-Current Detection. This pin is typically connected to the over current output

of the downstream port power switch for Port 1.

0 = An over current event has occurred

1 = An over current event has not occurred

When GANGED power management is enabled, this pin or one of the other OVERCURz pins

must be connected to the over current output of the power switch or circuit which detects the

over current conditions. For the case when another OVERCURz pin is used, this pin can be

left unconnected.

USB_SSTXP_DN2

USB SuperSpeed transmitter differential pair (positive)

USB_SSTXM_DN2

USB SuperSpeed transmitter differential pair (negative)

USB_SSRXP_DN2

USB SuperSpeed receiver differential pair (positive)

USB_SSRXM_DN2

USB SuperSpeed receiver differential pair (negative)

USB_DP_DN2

I/O

USB High-speed differential transceiver (positive)

USB_DM_DN2

I/O

USB High-speed differential transceiver (negative)

PWRCTL2/BATEN2

I/O, PD

USB Port 2 Power On Control for Downstream Power/Battery Charging Enable. The pin is

used for control of the downstream power switch for Port 2. This pin be left unconnected if

power management is not implemented.

In addition, the value of the pin is sampled at the de-assertion of reset to determine the value

of the battery charging support for Port 2 as indicated in the Battery Charging Support

0 = Battery charging not supported

1 = Battery charging supported

TUSB8044AI bảng dữ liệu(PDF) 5 Page - Texas Instruments

TUSB8044AI bảng dữ liệu(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

bảng dữ liệu tải về

Link URL