STM32F070CB datasheet(58/83 Pages) STMICROELECTRONICS

58 / 83 page

Electrical characteristics

STM32F070CB/RB/C6/F6

58/83

DocID027114 Rev 3

Output driving current

The GPIOs (general purpose input/outputs) can sink or source up to +/-8 mA, and sink or

source up to +/- 20 mA (with a relaxed VOL/VOH).

In the user application, the number of I/O pins which can drive current must be limited to

respect the absolute maximum rating specified in Section 6.2:

•

The sum of the currents sourced by all the I/Os on VDDIOx, plus the maximum

consumption of the MCU sourced on VDD, cannot exceed the absolute maximum rating

ΣIVDD (see Table 17: Voltage characteristics).

•

The sum of the currents sunk by all the I/Os on VSS, plus the maximum consumption of

the MCU sunk on VSS, cannot exceed the absolute maximum rating ΣIVSS (see

Table 17: Voltage characteristics).

Output voltage levels

Unless otherwise specified, the parameters given in the table below are derived from tests

performed under the ambient temperature and supply voltage conditions summarized in

Table 20: General operating conditions. All I/Os are CMOS- and TTL-compliant (FT, TTa or

TC unless otherwise specified).

Input/output AC characteristics

The definition and values of input/output AC characteristics are given in Figure 17 and

Table 47, respectively.

Unless otherwise specified, the parameters given are derived from tests performed under

the ambient temperature and supply voltage conditions summarized in Table 20: General

operating conditions.

Table 46. Output voltage characteristics(1)

Symbol

Parameter

Conditions

Min

Max

Unit

VOL

Output low level voltage for an I/O pin

|IIO| = 8 mA

VDDIOx

≥ 2.7 V

-0.4

VOH

Output high level voltage for an I/O pin

VDDIOx–0.4

VOL(2)

Output low level voltage for an I/O pin

|IIO| = 20 mA

VDDIOx

≥ 2.7 V

-1.3

VOH(2)

Output high level voltage for an I/O pin

VDDIOx–1.3

VOL(2)

Output low level voltage for an I/O pin

|IIO| = 6 mA

-0.4

VOH(2)

Output high level voltage for an I/O pin

VDDIOx–0.4

VOLFm+(2)

Output low level voltage for an FTf I/O pin in

Fm+ mode

|IIO| = 20 mA

VDDIOx

≥ 2.7 V

-0.4

|IIO| = 10 mA

0.4

1. The IIO current sourced or sunk by the device must always respect the absolute maximum rating specified in Table 17:

Voltage characteristics, and the sum of the currents sourced or sunk by all the I/Os (I/O ports and control pins) must always

respect the absolute maximum ratings

ΣIIO.

2. Data based on characterization results. Not tested in production.

STM32F070CB bảng dữ liệu(PDF) 58 Page - STMicroelectronics

STM32F070CB bảng dữ liệu(HTML) 58 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83

bảng dữ liệu tải về

Link URL