ST16C552AIJ68 datasheet(22/39 Pages) EXAR

22 / 39 page

ST16C552/552A

Rev. 3.40

LCR

Parity selection

Bit-5

Bit-4

Bit-3

No parity

Odd parity

Even parity

Force parity odd parity

Forced even parity

LCR BIT-6:

When enabled the Break control bit causes a break

condition to be transmitted (the TX output is forced to

a logic 0 state). This condition exists until disabled by

setting LCR bit-6 to a logic 0.

Logic 0 = No TX break condition. (normal default

condition)

Logic 1 = Forces the transmitter output (TX) to a logic

0 for alerting the remote receiver to a line break

condition.

LCR BIT-7:

The internal baud rate counter latch and Enhance

Feature mode enable.

Logic 0 = Divisor latch disabled. (normal default

condition)

Logic 1 = Divisor latch and enhanced feature register

enabled.

Modem Control Register (MCR)

This register controls the interface with the modem or

a peripheral device.

MCR BIT-0:

Logic 0 = Force -DTR output to a logic 1. (normal

default condition)

Logic 1 = Force -DTR output to a logic 0.

MCR BIT-1:

Logic 0 = Force -RTS output to a logic 1. (normal

default condition)

Logic 1 = Force -RTS output to a logic 0.

MCR BIT-2:

This bit is used in the Loop-back mode only. In the

loop-back mode this bit is use to write the state of the

modem -RI interface signal.

MCR BIT-3: (Used to control the modem -CD signal

in the loop-back mode.)

Logic 0 = Forces INT (A-B) outputs to the three state

mode. (normal default condition) In the Loop-back

mode, sets -CD internally to a logic 1.

Logic 1 = Forces the INT (A-B) outputs to the active

mode. In the Loop-back mode, sets -CD internally to

a logic 0.

MCR BIT-4:

Logic 0 = Disable loop-back mode. (normal default

condition)

Logic 1 = Enable local loop-back mode (diagnostics).

MCR BIT 5-6:

Not Used - initialized to a logic 0.

MCR BIT-7:

Logic 0 = Disable power down mode. (normal, default

condition, 552 only)

Logic 1 = Enable power down mode (IER bit-5 must

also be a logic 1 before power down will be activated).

Line Status Register (LSR)

This register provides the status of data transfers

between. the 552/552A and the CPU.

LSR BIT-0:

Logic 0 = No data in receive holding register or FIFO.

(normal default condition)

Logic 1 = Data has been received and is saved in the

receive holding register or FIFO.

LSR BIT-1:

Logic 0 = No overrun error. (normal default condition)

Logic 1 = Overrun error. A data overrun error occurred

in the receive shift register. This happens when addi-

tional data arrives while the FIFO is full. In this case

the previous data in the shift register is overwritten.

Note that under this condition the data byte in the

receive shift register is not transferred into the FIFO,

therefore the data in the FIFO is not corrupted by the

error.

ST16C552AIJ68 bảng dữ liệu(PDF) 22 Page - Exar Corporation

ST16C552AIJ68 bảng dữ liệu(HTML) 22 Page - Exar Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

bảng dữ liệu tải về

Link URL