CAP1114 datasheet(26/102 Pages) MICROCHIP

26 / 102 page

Multiple Channel Capacitive Touch Sensor and LED Driver

Datasheet

Revision 1.1 (02-04-11)

SMSC CAP1114

DATASHEET

5.4.1

Multiple Button Presses

If multiple sensor buttons (with a programmable threshold - see Section 6.23) are simultaneously

detected, only the first N buttons that are detected are flagged. All other buttons are ignored.

Furthermore, the device remembers which buttons were legitimate so new touches are not detected

so long as N buttons are pressed.

Likewise, if too many (based on the programmed threshold - see Section 6.23) grouped sensor

presses are detected, the device will block all press detections on the grouped buttons and cancel any

current presses as if the sensor had been released.

5.4.2

Lid Closure

To detect lid closure or other similar events, lid closure sensor thresholds can be set. A Lid Closure

Event can be flagged based on either a minimum number of sensors or on specific sensors

simultaneously exceeding the lid closure threshold. An interrupt can also be generated. During a Lid

Closure Event, all touches are blocked.

5.4.3

Grouped Sensors (CS8 - CS14)

Capacitive Touch Sensors 8 through 14 inclusive may be grouped as a single entity (which is the

default state). Each sensor is sampled independently; however, for purposes of activation,

recalibration, and repeat rates, all of them are treated as one group. The Group also has different

controls and allows for different behavior such as sliding, tapping, or press and hold.

The grouped sensors may be ungrouped as described in Section 5.6.

5.4.4

Sensing Cycle

Each Capacitive Touch Sensor has controls to be activated and included in the sensing cycle. When

the device is active, it automatically initiates a sensing cycle and repeats the cycle every time it

finishes. The cycle polls through each active Sensor starting with CS1 and extending through CS14.

As each Capacitive Touch Sensor is polled, its measurement is compared against a baseline “not

touched” measurement. If the delta measurement is large enough, a touch is detected and an interrupt

generated.

5.4.5

Proximity Detection

Sensor CS1 can be configured to detect changes in capacitance due to proximity of a touch. This

circuitry detects the change of capacitance that is generated as an object approaches, but does not

physically touch, the CS1 sensor. When proximity detection is enabled, the signal is boosted by 8x to

detect very small capacitance changes. Separate controls determine averaging and sensitivity for

proximity (see Section 6.35, "Proximity Control Register").

5.4.6

Recalibrating Sensors

Each sensor is regularly recalibrated at an adjustable rate. By default, the recalibration routine stores

the average 256 previous measurements and periodically updates the base “Not Touched” setting for

the Capacitive Touch Sensor input. This routine is disabled automatically if a touch is detected so the

touch does not factor into the base “Not Touched” setting.

5.4.7

Low Frequency Noise Detection

Each sensor has a noise detector that will sense if low frequency noise is injected onto the input with

sufficient power to corrupt the readings. This noise detector has a fixed threshold above and below

the rail that will trigger when noise is present. If low frequency noise is detected on a CS line, that

sample is removed and not compared against the threshold.

CAP1114 bảng dữ liệu(PDF) 26 Page - Microchip Technology

CAP1114 bảng dữ liệu(HTML) 26 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL