công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

CY7C63413-PVC bảng dữ liệu(PDF) 20 Page - Cypress Semiconductor

tên linh kiện CY7C63413-PVC
Giải thích chi tiết về linh kiện  Low-speed USB Peripheral Controller
PDF  36 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  CYPRESS [Cypress Semiconductor]
Trang chủ  http://www.cypress.com
Logo CYPRESS - Cypress Semiconductor

CY7C63413-PVC bảng dữ liệu(HTML) 20 Page - Cypress Semiconductor

Back Button CY7C63413-PVC Datasheet HTML 16Page - Cypress Semiconductor CY7C63413-PVC Datasheet HTML 17Page - Cypress Semiconductor CY7C63413-PVC Datasheet HTML 18Page - Cypress Semiconductor CY7C63413-PVC Datasheet HTML 19Page - Cypress Semiconductor CY7C63413-PVC Datasheet HTML 20Page - Cypress Semiconductor CY7C63413-PVC Datasheet HTML 21Page - Cypress Semiconductor CY7C63413-PVC Datasheet HTML 22Page - Cypress Semiconductor CY7C63413-PVC Datasheet HTML 23Page - Cypress Semiconductor CY7C63413-PVC Datasheet HTML 24Page - Cypress Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 20 / 36 page
background image
CY7C63411/12/13
CY7C63511/12/13
CY7C63612/13
FOR
FOR
Document #: 38-08027 Rev. **
Page 20 of 36
10.2
DAC Isink Registers
Each DAC I/O pin has an associated DAC Isink register to program the output sink current when the output is driven LOW. The
first Isink register (0x38h) controls the current for DAC[0], the second (0x39h) for DAC[1], and so on until the Isink register at
0x3Fh controls the current to DAC[7].
11.0
USB Serial Interface Engine (SIE)
The SIE allows the microcontroller to communicate with the USB host. The SIE simplifies the interface between the microcontroller
and USB by incorporating hardware that handles the following USB bus activity independently of the microcontroller:
• Bit stuffing/unstuffing
• Checksum generation/checking
• ACK/NAK
• Token type identification
• Address checking
Firmware is required to handle the rest of the USB interface with the following tasks:
• Coordinate enumeration by responding to set-up packets
• Fill and empty the FIFOs
• Suspend/Resume coordination
• Verify and select Data toggle values
11.1
USB Enumeration
The enumeration sequence is shown below:
1. The host computer sends a Setup packet followed by a Data packet to USB address 0 requesting the Device descriptor.
2. The USB Controller decodes the request and retrieves its Device descriptor from the program memory space.
3. The host computer performs a control read sequence and the USB Controller responds by sending the Device descriptor over
the USB bus.
4. After receiving the descriptor, the host computer sends a Setup packet followed by a Data packet to address 0 assigning a
new USB address to the device.
5. The USB Controller stores the new address in its USB Device Address Register after the no-data control sequence is complete.
6. The host sends a request for the Device descriptor using the new USB address.
7. The USB Controller decodes the request and retrieves the Device descriptor from the program memory.
8. The host performs a control read sequence and the USB Controller responds by sending its Device descriptor over the USB bus.
9. The host generates control reads to the USB Controller to request the Configuration and Report descriptors.
10.The USB Controller retrieves the descriptors from its program space and returns the data to the host over the USB.
11.2
PS/2 Operation
PS/2 operation is possible with the CY7C634XX/5XX/6XX series through the use of firmware and several operating modes. The
first enabling feature:
1. USB Bus reset on D+ and D
− is an interrupt that can be disabled;
2. USB traffic can be disabled via bit 7 of the USB register;
3. D+ and D
− can be monitored and driven via firmware as independent port bits.
Bits 5 and 4 of the Upstream Status and Control register are directly connected to the D+ and D
− USB pins of the CY7C634XX/
5XX/6XX. These pins constantly monitor the levels of these signals with CMOS input thresholds. Firmware can poll and decode
these signals as PS/2 clock and data.
Bits [2:0] defaults to ‘000’ at reset which allows the USB SIE to control output on D+ and D
−. Firmware can override the SIE and
directly control the state of these pins via these 3 control bits. Since PS/2 is an open drain signaling protocol, these modes allow
all 4 PS/2 states to be generated on the D+ and D
− pins
Reserved
Isink Value
Isink[3]
Isink[2]
Isink[1]
Isink[0]
Figure 10-5. DAC Port Isink 0x38h to 0x3Fh (write only)



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com