ADC12L032CIWM datasheet(25/36 Pages) NSC

25 / 36 page

Application Hints (Continued)

output during these instructions is from conversion N which

was started during I/O sequence 1. The Configuration Modi-

fication timing diagram describes in detail the sequence of

events necessary for a Data Out without Sign, Data Out with

Sign, or 6/10/18/34 CCLK Acquisition time mode selection.

Table 5 describes the actual data necessary to be input to

the ADC to accomplish this configuration modification. The

next instruction, shown in

Figure 8, issued to the A/D starts

conversion N+1 with 8 bits of resolution formatted MSB first.

Again the data output during this I/O cycle is the data from

conversion N.

The number of SCLKs applied to the A/D during any conver-

sion I/O sequence should vary in accord with the data out

word format chosen during the previous conversion I/O se-

quence. The various formats and resolutions available are

shown in

Table 1.In Figure 8, since 8-bit without sign MSB

first format was chosen during I/O sequence 4, the number

of SCLKs required during I/O sequence 5 is 8. In the follow-

ing I/O sequence the format changes to 12-bit without sine

MSB first; therefore the number of SCLKs required during

I/O sequence 6 changes accordingly to 12.

1.3 CS Low Continuously Considerations

When CS is continuously low, it is important to transmit the

exact number of SCLK pulses that the ADC expects. Not do-

ing so will desynchronize the serial communications to the

ADC. When the supply power is first applied to the ADC, it

will expect to see 13 SCLK pulses for each I/O transmission.

The number of SCLK pulses that the ADC expects to see is

the same as the digital output word length. The digital output

word length is controlled by the Data Out (DO) format. The

DO format maybe changed any time a conversion is started

or when the sign bit is turned on or off. The table below de-

tails out the number of clock periods required for different

DO formats:

Number of

DO Format

SCLKs

Expected

8-Bit MSB or LSB First

SIGN OFF

SIGN ON

12-Bit MSB or LSB First

SIGN OFF

SIGN ON

16-Bit MSB or LSB first

SIGN OFF

SIGN ON

If erroneous SCLK pulses desynchronize the communica-

tions, the simplest way to recover is by cycling the power

supply to the device. Not being able to easily resynchronize

the device is a shortcoming of leaving CS low continuously.

The number of clock pulses required for an I/O exchange

may be different for the case when CS is left low continu-

ously vs. the case when CS is cycled. Take the I/O sequence

detailed in

Figure 7 (Typical Power Supply Sequence) as an

example. The table below lists the number of SCLK pulses

required for each instruction:

Instruction

CS Low

CS Strobed

Continuously

Auto Cal

13 SCLKs

8 SCLKs

Read Status

13 SCLKs

8 SCLKs

Read Status

13 SCLKs

8 SCLKs

12-Bit + Sign Conv 1

13 SCLKs

8 SCLKs

12-Bit + Sign Conv 2

13 SCLKs

1.4 Analog Input Channel Selection

The data input on DI also selects the channel configuration

for a particular A/D conversion (See

Tables 2, 3, 4, 5). In Fig-

ure 8 the only times when the channel configuration could be

modified would be during I/O sequences 1, 4, 5 and 6. Input

channels are reselected before the start of each new conver-

sion. Shown below is the data bit stream required on DI, dur-

ing I/O sequence number 4 in

Figure 8, to set CH1 as the

positive input and CH0 as the negative input for the different

versions of ADCs:

Part

Number

DI Data

DI0

DI1

DI2

DI3

DI4

DI5

DI6

DI7

ADC12L030

LHL

ADC12L032

LHL

ADC12L034

LLL

ADC12L038

LLLL

Where X can be a logic high (H) or low (L).

1.5 Power Up/Down

The ADC may be powered down at any time by taking the

PD pin HIGH or by the instruction input on DI (see

Tables 5,

6, and the Power Up/Down timing diagrams). When the ADC

is powered down in this way the circuitry necessary for an

A/D conversion is deactivated. The circuitry necessary for

digital I/O is kept active. Hardware power up/down is con-

trolled by the state of the PD pin. Software power up/down is

controlled by the instruction issued to the ADC. If a software

power up instruction is issued to the ADC while a hardware

power down is in effect (PD pin high) the device will remain

DS011830-37

FIGURE 8. Changing the ADC’s Conversion Configuration

ADC12L032CIWM bảng dữ liệu(PDF) 25 Page - National Semiconductor (TI)

ADC12L032CIWM bảng dữ liệu(HTML) 25 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

bảng dữ liệu tải về

Link URL