CAP1298 datasheet(40/68 Pages) MICROCHIP

40 / 68 page

CAP1298

DS00001571B-page 40

 2013-2015 Microchip Technology Inc.

Bit 6 - CS7_RPT_EN - Enables the repeat rate for capacitive touch sensor input 7.

Bit 5 - CS6_RPT_EN - Enables the repeat rate for capacitive touch sensor input 6.

Bit 4 - CS5_RPT_EN - Enables the repeat rate for capacitive touch sensor input 5.

Bit 3 - CS4_RPT_EN - Enables the repeat rate for capacitive touch sensor input 4.

Bit 2 - CS3_RPT_EN - Enables the repeat rate for capacitive touch sensor input 3.

Bit 1 - CS2_RPT_EN - Enables the repeat rate for capacitive touch sensor input 2.

Bit 0 - CS1_RPT_EN - Enables the repeat rate for capacitive touch sensor input 1.

5.13

Signal Guard Enable Register

The Signal Guard Enable register enables the signal guard for the specified sensor inputs as described in Section 4.5.1,

"Signal Guard". When the signal guard is enabled, CS5 is disabled.

For all bits in this register:

• ‘0’ (default) - The signal guard is disabled for the specified sensor input.

• ‘1’ - The signal guard is enabled for the specified sensor input.

Bit 7 - CS8_SG_EN - Enables the signal guard for capacitive touch sensor input 8.

Bit 6 - CS7_SG_EN - Enables the signal guard for capacitive touch sensor input 7.

Bit 5 - CS6_SG_EN - Enables the signal guard for capacitive touch sensor input 6.

Bit 3 - CS4_SG_EN - Enables the signal guard for capacitive touch sensor input 4.

Bit 2 - CS3_SG_EN - Enables the signal guard for capacitive touch sensor input 3.

Bit 1 - CS2_SG_EN - Enables the signal guard for capacitive touch sensor input 2.

Bit 0 - CS1_SG_EN - Enables the signal guard for capacitive touch sensor input 1.

5.14

Multiple Touch Configuration Register

The Multiple Touch Configuration register controls the settings for the multiple touch detection circuitry. These settings

determine the number of simultaneous buttons that may be pressed before additional buttons are blocked and the MULT

status bit is set.

Bit 7 - MULT_BLK_EN - Enables the multiple button blocking circuitry.

• ‘0’ - The multiple touch circuitry is disabled. The device will not block multiple touches.

• ‘1’ (default) - The multiple touch circuitry is enabled. The device will flag the number of touches equal to pro-

grammed multiple touch threshold and block all others. It will remember which sensor inputs are valid and block all

others until that sensor pad has been released. Once a sensor pad has been released, the N detected touches

TABLE 5-25:

SIGNAL GUARD ENABLE REGISTER

Addr

R/W

B4B3B2B1

Default

29h

R/W

Signal

Guard

Enable

CS8_

SG_EN

CS7_

SG_EN

CS6_

SG_EN

CS4_

SG_EN

CS3_

SG_EN

CS2_

SG_EN

CS1_

SG_EN

00h

TABLE 5-26:

MULTIPLE TOUCH CONFIGURATION

Addr

R/W

Default

2Ah

R/W

Multiple Touch

Config

MULT_

BLK_

B_MULT_T[1:0]

80h

CAP1298 bảng dữ liệu(PDF) 40 Page - Microchip Technology

CAP1298 bảng dữ liệu(HTML) 40 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

bảng dữ liệu tải về

Link URL