CDCE62005 datasheet(71/85 Pages) TI1

71 / 85 page

CDCE62005

www.ti.com

SCAS862F – NOVEMBER 2008 – REVISED JANUARY 2015

Typical Application (continued)

9.2.2 Detailed Design Procedure

Step 1. From Figure 47, it can be inferred that the relationship between the output frequency and the input

frequency is described by these equations,

where:

FVCO = FOUT ´ P ´ N

(17)

provided that:

80 kHz < (FIN/M) < 40 MHz

(18)

and:

1750 MHz < (FOUT ´ P ´ N) < 2350 MHz

(19)

Step 2. Keep in mind the following while satisfying the equations in Step 1:

•

The P divider can be chosen to be 1, 2, 3, 4, 5, up to 80

•

The internal VCO range is from 1.75 GHz to 2.35 GHz

•

The input (M) and prescaler (N) dividers can be chosen from Table 22 and Table 26.

•

The FB divider can be chosen from the values in Table 23 and Table 24.

Step 3. Given multiple desired output frequencies and the input frequency, the first step would be to establish M,

N, and FB divider values for different P divider settings to satisfy these equations:

FIN = FOUT1 x (M x P1) / (N x FB)

(20)

FIN = FOUT2 x (M x P2) / (N x FB)

(21)

FIN = FOUT3 x (M x P3) / (N x FB)

(22)

FIN = FOUT4 x (M x P4) / (N x FB)

(23)

FIN = FOUT5 x (M x P5) / (N x FB)

(24)

(FVCO/ N) = FOUT1 x P1 = FOUT2 x P2 = FOUT3 x P3 = FOUT4 x P4 = FOUT5 x P5

(25)

Such that these parameters are valid:

•

The common PFD frequency is always less than 40 MHz.

•

The VCXO frequency is the same for deriving all outputs.

Using the example to derive these outputs, it can be seen that there is not an output divider (P5) that will

generate a 25-MHz output. However, the output MUX value of output 5 can be chosen to directly bypass the 25-

MHz input clock to output 5. Therefore, in order to use a common VCO frequency, the P dividers to be used are:

•

P1 = 4

•

P2 = 4

•

P3 = 5

•

P4 = 5

•

P5 = 1

The common VCO frequency is 1875 MHz and is VCO1. The output MUX for outputs 1 to 4 are set to the

PLL/VCO outputs. Moreover, the FB divider to be used is:

FB = 100

(26)

The N divider to be used is:

N = 3

(27)

These values ensure that the (FIN/M) ratio is within 40 MHz and is set at 6.25 MHz. Thus, the M divider to be

used is:

M = 4

(28)

Figure 47 illustrates this configuration.

Submit Documentation Feedback

Product Folder Links: CDCE62005

CDCE62005 bảng dữ liệu(PDF) 71 Page - Texas Instruments

CDCE62005 bảng dữ liệu(HTML) 71 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85

bảng dữ liệu tải về

Link URL