PIC17C752-08SLASHP datasheet(104/320 Pages) MICROCHIP

104 / 320 page

PIC17C75X

DS30264A-page 104

Preliminary

13.2.4

EXTERNAL CLOCK INPUT FOR TIMER3

When TMR3CS is set, the 16-bit TMR3 increments on

the falling edge of clock input TCLK3. The input on the

RB5/TCLK3 pin is sampled and synchronized by the

internal phase clocks twice every instruction cycle. This

causes a delay from the time a falling edge appears on

TCLK3 to the time TMR3 is actually incremented. For

the external clock input timing requirements, see the

Electrical Speciﬁcation section. Figure 13-10 shows

the timing diagram when operating from an external

clock.

13.2.5

READING/WRITING TIMER3

Since Timer3 is a 16-bit timer and only 8-bits at a time

can be read or written, care should be taken when

reading or writing while the timer is running. The best

method is to stop the timer, perform any read or write

operation, and then restart Timer3 (using the TMR3ON

bit). However, if it is necessary to keep Timer3 free-run-

ning, care must be taken. For writing to the 16-bit

TMR3, Example 13-2 may be used. For reading the

16-bit TMR3, Example 13-3 may be used. Interrupts

must be disabled during this routine.

EXAMPLE 13-2: WRITING TO TMR3

EXAMPLE 13-3: READING FROM TMR3

FIGURE 13-10: TIMER1, TIMER2, AND TIMER3 OPERATION (IN COUNTER MODE)

BSF

CPUSTA, GLINTD

; Disable interrupts

MOVFP

RAM_L,

TMR3L

;

MOVFP

RAM_H,

TMR3H

;

BCF

CPUSTA, GLINTD

; Done, enable interrupts

MOVPF

TMR3L, TMPLO

; read low TMR3

MOVPF

TMR3H, TMPHI

; read high TMR3

MOVFP

TMPLO, WREG

; tmplo

−> wreg

CPFSLT

TMR3L, WREG

; TMR3L < wreg?

RETURN

; no then return

MOVPF

TMR3L, TMPLO

; read low TMR3

MOVPF

TMR3H, TMPHI

; read high TMR3

RETURN

; return

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

Instruction

executed

MOVWF

MOVFP

TMRx,W

TMRx

MOVFP

TMRx,W

Write to TMRx

Read TMRx

34h

35h

A8h

A9h

00h

'A9h'

TCLK12

TMR1, TMR2, or TMR3

PR1, PR2, or PR3H:PR3L

WR_TMR

RD_TMR

TMRxIF

Note 1: TCLK12 is sampled in Q2 and Q4.

2: ↓ indicates a sampling point.

3: The latency from TCLK12

↓ to timer increment is between 2Tosc and 6Tosc.

or TCLK3

PIC17C752-08/P bảng dữ liệu(PDF) 104 Page - Microchip Technology

PIC17C752-08/P bảng dữ liệu(HTML) 104 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL