| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC16F872/SP bảng dữ liệu(PDF) 61 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC16F872/SP bảng dữ liệu(HTML) 61 Page - Microchip Technology |
|
61 / 160 page ![]() © 1999 Microchip Technology Inc. Preliminary DS30221A-page 61 PIC16F872 9.2 MSSP I2C Operation The MSSP module in I2C mode fully implements all master and slave functions (including general call sup- port) and provides interrupts-on-start and stop bits in hardware to determine a free bus (multi-master func- tion). The MSSP module implements the standard mode specifications, as well as 7-bit and 10-bit addressing. Refer to Application Note AN578, "Use of the SSP Module in the I 2C Multi-Master Environment." A "glitch" filter is on the SCL and SDA pins when the pin is an input. This filter operates in both the 100 kHz and 400 kHz modes. In the 100 kHz mode, when these pins are an output, there is a slew rate control of the pin that is independent of device frequency. FIGURE 9-5: I2C SLAVE MODE BLOCK DIAGRAM Two pins are used for data transfer. These are the SCL pin, which is the clock, and the SDA pin, which is the data. The SDA and SCL pins are automatically config- ured when the I2C mode is enabled. The SSP module functions are enabled by setting SSP Enable bit SSPEN (SSPCON<5>). The MSSP module has six registers for I2C operation. They are the: • SSP Control Register (SSPCON) • SSP Control Register2 (SSPCON2) • SSP Status Register (SSPSTAT) • Serial Receive/Transmit Buffer (SSPBUF) • SSP Shift Register (SSPSR) - Not directly accessible • SSP Address Register (SSPADD) The SSPCON register allows control of the I2C opera- tion. Four mode selection bits (SSPCON<3:0>) allow one of the following I2C modes to be selected: •I2C Slave mode (7-bit address) •I2C Slave mode (10-bit address) •I2C Master mode, clock = OSC/4 (SSPADD +1) Before selecting any I2C mode, the SCL and SDA pins must be programmed to inputs by setting the appropri- ate TRIS bits. Selecting an I2C mode, by setting the SSPEN bit, enables the SCL and SDA pins to be used as the clock and data lines in I2C mode. The CKE bit (SSPSTAT<6:7>) sets the levels of the SDA and SCL pins in either Master or Slave mode. When CKE = 1, the levels will conform to the SMBUS specification. When CKE = 0, the levels will conform to the I2C specification. Read Write SSPSR reg Match detect SSPADD reg Start and Stop bit detect SSPBUF reg Internal Data Bus Addr Match Set, Reset S, P bits (SSPSTAT reg) SCL Shift Clock MSb LSb SDA |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |