| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MAX459CPL bảng dữ liệu(PDF) 10 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX459CPL bảng dữ liệu(HTML) 10 Page - Maxim Integrated Products |
|
10 / 16 page ![]() 8x4 Video Crosspoint Switches with Buffers 10 ______________________________________________________________________________________ to their switch registers. As long as either – W — R – or – C — E – is high, the input register will not change. The switch reg- ister will pass any new data on the falling transition of – U — P — D — A — T — E – . Each register of the switch-register bank controls the inputs to one amplifier. With – U — P — D — A — T — E – low, the switch registers are transparent and switch connection is con- trolled by the input register. However, if – U — P — D — A — T — E – is high, the switch register is latched and any change in data by the input register will not affect the amplifier output state. Two register banks are used so that data can be loaded into input registers without affecting the switch/amplifier selection. This allows amplifiers to be programmed and then changed simultaneously. When the registers are not latched, they are made transparent. Use data bit D3 to disable the amplifier selected by A0–A1 and place its output in high-impedance mode. As an example, the code to disable OUT0 is as follows: Pin Name: D3 D2 D1 D0 A1 A0 Input Code: 1 X X X 0 0 When operating in parallel mode, C — S – must be wired high and SCLK and DIN should be grounded, as shown in Figure 3. Refer to Figure 4 for the correct timing rela- tionships. Digital Section—Serial Mode The MAX458/MAX459 use a three-wire serial interface that is compatible with SPI, QPSI and Microwire inter- faces. Serial mode, shown in Figure 5, is enabled when – W — R – , – U — P — D — A — T — E – , and – C — E – are held high and – C — S – goes low. Figures 6 and 7 show serial-mode timing. Figure 8 shows the MAX458/MAX459 configured for serial oper- ation. Figure 9 shows the Microwire connection, and Figure 10 shows the SPI/QSPI connection. The serial output, DOUT, allows cascading of two or more crosspoint switches to create larger arrays. The data at DOUT is delayed by 16 cycles plus one clock pulse width at DIN. DOUT changes on SCLK’s falling edge when – C — S – is low. When – C — S – is high, DOUT remains in the state of the last data bit. The MAX458/MAX459 input data in 16-bit blocks. SPI and Microwire interfaces output data in 8-bit blocks, thereby requiring two write cycles to input data. The QSPI interface allows variable word lengths from 8 to 16 bits and can be loaded into the crosspoint in one write cycle. SPI and Microwire limit clock rates to 2MHz, while the QSPI maximum clock rate is 4MHz. ADDRESS VALID A0/A1 CE WR UPDATE tADS tCES tWR tCEH tDS tADH DATA VALID D0–D3 tDH tWRS tUP tUPS Figure 4. Parallel-Mode Timing |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |