DM300018 datasheet(94/115 Pages) MICROCHIP

94 / 115 page

dsPICDEM 2 Development Board User’s Guide

DS51558A-page 88

TABLE 14-1:

dsPICDEM™ 1.1 DEVELOPMENT BOARD HARDWARE

14.1.1

Power Supply

The dsPICDEM™ 2 Development Board may be powered by a +9V AC/DC wall

adapter. A DC voltage regulator is provided so as to regulate the +9V input from the

wall adaptor and supply +5V to VDD and AVDD pins on the dsPIC30F device. In order

to supply power to the board from a wall adaptor, the jumpers JP1 and JP2 need to be

installed and power should be supplied via the J4 jack. The PWR ON LED, D1 will

illuminate if the power has been applied to the board appropriately.

The schematics of the power supply circuits are shown in Figure A-8: “dsPICDEM™

2 Development Board Schematic (Sheet 7 of 7)”.

No.

Hardware Element

No.

Hardware Element

CAN Port

(see Section 14.1.6)

Switch S6 header

(see Section 14.1.8)

2CAN Transceiver

(see Section 14.1.6)

Analog Potentiometer

(see Section 14.1.12)

CAN Header

(see Section 14.1.6)

Analog Potentiometer Header

(see Section 14.1.12)

External Power Supply Inputs

(see Section 14.1.1)

LCD Graphic Display

(see )

Power On LED

(see Section 14.1.1)

SPI™ Controller for LCD

(see Section 14.1.5)

Power Supply jumpers

(see Section 14.1.1)

SPI™ Programming Header

(see Section 14.1.5)

Voltage Regulator

(see Section 14.1.1)

LCD Controller Header

(see Section 14.1.5)

UART 1 Header

(see Section 14.1.7)

Temperature Sensor Header

(see Section 14.1.11)

DIP Switch, debug selector for general

purpose device sockets

(see Section 14.1.4)

Temperature Sensor

(see Section 14.1.11)

Alternate UART 1 header

(see Section 14.1.7)

External Connection Headers

(see Section 14.1.10)

Device Headers, concentric sockets

for dsPIC30F devices

(see Section 14.1.2)

Crystal Oscillator, for motor control

devices

(see Section 14.1.3)

Crystal Oscillator, for General Purpose

Devices

(see Section 14.1.3)

DIP Switch, Debug Selector for motor

control device sockets

(see Section 14.1.4)

Reset Pushbutton Switch

(see Section 14.1.13)

dsPIC30F4011 Device

(see Section 14.1.2)

UART 2 header

(see Section 14.1.7)

Programming Selector DIP Switch

(see Section 14.1.4)

Output LEDs

(see Section 14.1.9)

ICD Connector

(see Section 14.1.4)

LED Header

(see Section 14.1.9)

UART Transceiver

(seeSection 14.1.7)

Pushbutton Switches S5 and S6

(see Section 14.1.8)

RS-232 Serial Port

(see Section 14.1.7)

Switch S5 header

(see Section 14.1.8)

DM300018 bảng dữ liệu(PDF) 94 Page - Microchip Technology

DM300018 bảng dữ liệu(HTML) 94 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL