07XSC200 datasheet(7/51 Pages) FREESCALE

7 / 51 page

Analog Integrated Circuit Device Data



Freescale Semiconductor

07XSC200

3.2

Static Electrical Characteristics

Table 3. Static Electrical Characteristics

Characteristics noted under conditions 6.0 V

VPWR  20 V, 3.0 V  VDD  5.5 V, -40 C  TA  125 C, GND = 0 V, unless

otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 °C under nominal conditions, unless

otherwise noted.

Characteristic

Symbol

Min

Typ

Max

Unit

POWER INPUTS

Battery Supply Voltage Range

• Fully Operational

• Extended mode(8)

VPWR

6.0

4.0

–

Battery Clamp Voltage(9)

VPWR(CLAMP)

VPWR Operating Supply Current

• Outputs commanded ON,

HS[0:1] open, IN[0:1] > VIH

IPWR(ON)

–6.5

VPWR Supply Current

• Outputs commanded OFF, OFF Open-load Detection Disabled, HS[0:1]

shorted to the ground with VDD = 5.5 V

WAKE > VIH or RSTB > VIH and IN[0:1] < VIL

IPWR(SBY)

–6.5

7.5

Sleep State Supply Current

VPWR = 12 V, RSTB = WAKE = CLOCK = IN[0:1] < VIL, HS[0:1] shorted to

ground

•TA = 25 °C

•TA = 85 °C

IPWR(SLEEP)

–

1.0

–

5.0

A

VDD Supply Voltage

VDD(ON)

3.0–5.5

VDD Supply Current at VDD = 5.5 V

• No SPI Communication

•8.0 MHz SPI Communication(10)

IDD(ON)

–

1.6

5.0

2.2

–

VDD Sleep State Current at VDD = 5.5 V

IDD(SLEEP)

––

5.0

A

Overvoltage Shutdown Threshold

VPWR(OV)

Overvoltage Shutdown Hysteresis

VPWR(OVHYS)

0.2

0.8

1.5

Undervoltage Shutdown Threshold(11)

VPWR(UV)

3.3

3.9

4.3

VPWR and VDD Power on Reset Threshold

VSUPPLY(POR)

0.5–0.9

VPWR(UV)

Recovery Undervoltage Threshold

VPWR(UV)_UP

3.4

4.1

4.5

VDD Supply Failure Threshold (for VPWR > VPWR(UV))

VDD(FAIL)

2.2

2.5

2.8

Notes

In extended mode, the functionality is guaranteed but not the electrical parameters. From 4.0 to 6.0 V voltage range, the device is only

protected with the thermal shutdown detection.

Measured with the outputs open.

10.

Typical value guaranteed per design.

11.

Output will automatically recover with time limited auto-retry to instructed state when VPWR voltage is restored to normal as long as the

VPWR degradation level did not go below the undervoltage power-ON reset threshold. This applies to all internal device logic that is

supplied by VPWR and assumes that the external VDD supply is within specification.

07XSC200 bảng dữ liệu(PDF) 7 Page - Freescale Semiconductor, Inc

07XSC200 bảng dữ liệu(HTML) 7 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

bảng dữ liệu tải về

Link URL