JS28F512P30TFA datasheet(14/86 Pages) MICRON

14 / 86 page

P30-65nm

Datasheet

Sept 2012

Order Number: 208042-0

4.0

Signals

Table 4:

TSOP and Easy BGA Signal Descriptions (Sheet 1 of 2)

Symbol

Type

Name and Function

A[MAX:1]

Input

ADDRESS INPUTS: Device address inputs. 512-Mbit: A[25:1], 1-Gbit: A[26:1], 2-Gbit: A[27:1].

Note: The virtual selection of the upper 1-Gbit die in the dual-die 2-Gbit configuration is

accomplished by setting A27 high (VIH).

DQ[15:0]

Input/

Output

DATA INPUT/OUTPUTS: Inputs data and commands during write cycles; outputs data during

reads of memory, Status Register, OTP Register, and Read Configuration Register. Data pins/balls

float when the CE# or OE# are deasserted. Data is internally latched during writes.

ADV#

Input

ADDRESS VALID: Active low input.

Easy BGA: During synchronous read operations, addresses are latched on the rising edge of ADV#,

or on the next valid CLK edge with ADV# low, whichever occurs first. In asynchronous mode, ADV#

can be either driven high to latch the address or held low throught the read cycle.

TSOP: ADV# must be tied to VSS or held low throughout the read cycle.

WARNING: Designs not using ADV# must tie it to VSS to allow addresses to flow through.

CE#

Input

CHIP ENABLE: Active low input. CE# low selects the associated flash memory die. When asserted,

flash internal control logic, input buffers, decoders, and sense amplifiers are active. When

deasserted, the associated flash die is deselected, power is reduced to standby levels, data and

WAIT outputs are placed in high-Z state.

WARNING: Chip Enable must be high when device is not in use.

CLK

Input

CLOCK: Synchronizes the device with the system’s bus frequency in synchronous-read mode.

During synchronous read operations, addresses are latched on the rising edge of ADV#, or on the

next valid CLK edge with ADV# low, whichever occurs first.

WARNING: Designs not using CLK for synchronous read mode must tie it to VCCQ or VSS.

OE#

Input

OUTPUT ENABLE: Active low input. OE# low enables the device’s output data buffers during read

cycles. OE# high places the data outputs and WAIT in High-Z.

RST#

Input

RESET: Active low input. RST# resets internal automation and inhibits write operations. This

provides data protection during power transitions. RST# high enables normal operation. Exit from

reset places the device in asynchronous read array mode.

WAIT

Output

WAIT: Indicates data valid in synchronous array or non-array burst reads. RCR.10, (WT) determines

its polarity when asserted. WAIT’s active output is VOL or VOH when CE# and OE# are VIL. WAIT is

high-Z if CE# or OE# is VIH.

• In synchronous array or non-array read modes, WAIT indicates invalid data when asserted and

valid data when deasserted.

• In asynchronous page mode, and all write modes, WAIT is deasserted.

WE#

Input

WRITE ENABLE: Active low input. WE# controls writes to the device. Address and data are latched

on the rising edge of WE#.

WP#

Input

WRITE PROTECT: Active low input. WP# low enables the lock-down mechanism. Blocks in lock-

down cannot be unlocked with the Unlock command. WP# high overrides the lock-down function

enabling blocks to be erased or programmed using software commands.

VPP

Power/

Input

ERASE AND PROGRAM POWER: A valid voltage on this pin allows erasing or programming.

Memory contents cannot be altered when VPP ≤ VPPLK. Block erase and program at invalid VPP

voltages should not be attempted.

Set VPP = VPPL for in-system program and erase operations. To accommodate resistor or diode drops

from the system supply, the VIH level of VPP can be as low as VPPL min. VPP must remain above VPPL

min to perform in-system flash modification. VPP may be 0 V during read operations.

VPPH can be applied to array blocks for 1000 cycles maximum. VPP can be connected to 9 V for a

cumulative total not to exceed 80 hours. Extended use of this pin at 9 V may reduce block cycling

capability.

VCC

Power

DEVICE CORE POWER SUPPLY: Core (logic) source voltage. Writes to the flash array are inhibited

when VCC ≤ VLKO. Operations at invalid VCC voltages should not be attempted.

VCCQ

Power

OUTPUT POWER SUPPLY: Output-driver source voltage.

VSS

Power

GROUND: Connect to system ground. Do not float any VSS connection.

JS28F512P30TFA bảng dữ liệu(PDF) 14 Page - Micron Technology

JS28F512P30TFA bảng dữ liệu(HTML) 14 Page - Micron Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

bảng dữ liệu tải về

Link URL