DSPIC33FJ64GS406 datasheet(327/456 Pages) MICROCHIP

327 / 456 page

 2009-2012 Microchip Technology Inc.

DS70591E-page 327

dsPIC33FJ32GS406/606/608/610 and dsPIC33FJ64GS406/606/608/610

bit 12-8

TRGSRC5<4:0>: Trigger 5 Source Selection bits

Selects trigger source for conversion of Analog Channels AN11 and AN10.

11111 = Timer2 period match

11110 = PWM Generator 8 current-limit ADC trigger

11101 = PWM Generator 7 current-limit ADC trigger

11100 = PWM Generator 6 current-limit ADC trigger

11011 = PWM Generator 5 current-limit ADC trigger

11010 = PWM Generator 4 current-limit ADC trigger

11001 = PWM Generator 3 current-limit ADC trigger

11000 = PWM Generator 2 current-limit ADC trigger

10111 = PWM Generator 1 current-limit ADC trigger

10110 = PWM Generator 9 secondary trigger selected

10101 = PWM Generator 8 secondary trigger selected

10100 = PWM Generator 7 secondary trigger selected

10011 = PWM Generator 6 secondary trigger selected

10010 = PWM Generator 5 secondary trigger selected

10001 = PWM Generator 4 secondary trigger selected

10000 = PWM Generator 3 secondary trigger selected

01111 = PWM Generator 2 secondary trigger selected

01110 = PWM Generator 1 secondary trigger selected

01101 = PWM secondary special event trigger selected

01100 = Timer1 period match

01011 = PWM Generator 8 primary trigger selected

01010 = PWM Generator 7 primary trigger selected

01001 = PWM Generator 6 primary trigger selected

01000 = PWM Generator 5 primary trigger selected

00111 = PWM Generator 4 primary trigger selected

00110 = PWM Generator 3 primary trigger selected

00101 = PWM Generator 2 primary trigger selected

00100 = PWM Generator 1 primary trigger selected

00011 = PWM special event trigger selected

00010 = Global software trigger selected

00001 = Individual software trigger selected

00000 = No conversion is enabled

bit 7

IRQEN4: Interrupt Request Enable 4 bit

1 = Enables IRQ generation when requested conversion of Channels AN9 and AN8 is completed

0 = IRQ is not generated

bit 6

PEND4: Pending Conversion Status 4 bit

1 = Conversion of Channels AN9 and AN8 is pending; set when selected trigger is asserted

0 = Conversion is complete

bit 5

SWTRG4: Software Trigger4 bit

1 = Starts conversion of AN9 and AN8 (if selected by TRGSRC bits)(1)

This bit is automatically cleared by hardware when the PEND4 bit is set.

0 = Conversion has not started

ADCPC2: ADC CONVERT PAIR CONTROL REGISTER 2 (CONTINUED)

Note 1: The trigger source must be set as a global software trigger prior to setting this bit to ‘1’. If other

conversions are in progress, the conversion is performed when the conversion resources are available.

dsPIC33FJ64GS406 bảng dữ liệu(PDF) 327 Page - Microchip Technology

dsPIC33FJ64GS406 bảng dữ liệu(HTML) 327 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL