SE33 datasheet(70/478 Pages) MICROCHIP

70 / 478 page

PIC16(L)F1946/47

DS41414D-page 70

 2010-2012 Microchip Technology Inc.

5.3

Clock Switching

The system clock source can be switched between

external and internal clock sources via software using

the System Clock Select (SCS) bits of the OSCCON

using the SCS bits:

• Default system oscillator determined by FOSC

bits in Configuration Words

• Timer1 32 kHz crystal oscillator

• Internal Oscillator Block (INTOSC)

5.3.1

SYSTEM CLOCK SELECT (SCS)

BITS

The System Clock Select (SCS) bits of the OSCCON

the CPU and peripherals.

• When the SCS bits of the OSCCON register = 00,

the system clock source is determined by value of

the FOSC<2:0> bits in the Configuration Words.

• When the SCS bits of the OSCCON register = 01,

the system clock source is the Timer1 oscillator.

• When the SCS bits of the OSCCON register = 1x,

the system clock source is chosen by the internal

oscillator frequency selected by the IRCF<3:0>

bits of the OSCCON register. After a Reset, the

SCS bits of the OSCCON register are always

cleared.

When switching between clock sources, a delay is

required to allow the new clock to stabilize. These oscil-

lator delays are shown in Table 5-1.

5.3.2

OSCILLATOR START-UP TIME-OUT

STATUS (OSTS) BIT

The Oscillator Start-up Time-out Status (OSTS) bit of

the OSCSTAT register indicates whether the system

clock is running from the external clock source, as

defined by the FOSC<2:0> bits in the Configuration

Words, or from the internal clock source. In particular,

OSTS indicates that the Oscillator Start-up Timer

(OST) has timed out for LP, XT or HS modes. The OST

does not reflect the status of the Timer1 oscillator.

5.3.3

TIMER1 OSCILLATOR

The Timer1 oscillator is a separate crystal oscillator

associated with the Timer1 peripheral. It is optimized

for timekeeping operations with a 32.768 kHz crystal

connected between the T1OSO and T1OSI device

pins.

The Timer1 oscillator is enabled using the T1OSCEN

control bit in the T1CON register. See Section 21.0

“Timer1 Module with Gate Control” for more

information about the Timer1 peripheral.

5.3.4

TIMER1 OSCILLATOR READY

(T1OSCR) BIT

The user must ensure that the Timer1 oscillator is

ready to be used before it is selected as a system clock

source. The Timer1 Oscillator Ready (T1OSCR) bit of

the OSCSTAT register indicates whether the Timer1

oscillator is ready to be used. After the T1OSCR bit is

set, the SCS bits can be configured to select the Timer1

oscillator.

Note:

Any automatic clock switch, which may

occur

from

Two-Speed

Start-up

Fail-Safe Clock Monitor, does not update

the SCS bits of the OSCCON register. The

user can monitor the OSTS bit of the

OSCSTAT register to determine the current

system clock source.

SE33 bảng dữ liệu(PDF) 70 Page - Microchip Technology

SE33 bảng dữ liệu(HTML) 70 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL