công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

HT47C06L bảng dữ liệu(PDF) 6 Page - Holtek Semiconductor Inc

tên linh kiện HT47C06L
Giải thích chi tiết về linh kiện  R-F Type Low Voltage 8-Bit Mask MCU
PDF  37 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  HOLTEK [Holtek Semiconductor Inc]
Trang chủ  http://www.holtek.com
Logo HOLTEK - Holtek Semiconductor Inc

HT47C06L bảng dữ liệu(HTML) 6 Page - Holtek Semiconductor Inc

Back Button HT47C06L Datasheet HTML 2Page - Holtek Semiconductor Inc HT47C06L Datasheet HTML 3Page - Holtek Semiconductor Inc HT47C06L Datasheet HTML 4Page - Holtek Semiconductor Inc HT47C06L Datasheet HTML 5Page - Holtek Semiconductor Inc HT47C06L Datasheet HTML 6Page - Holtek Semiconductor Inc HT47C06L Datasheet HTML 7Page - Holtek Semiconductor Inc HT47C06L Datasheet HTML 8Page - Holtek Semiconductor Inc HT47C06L Datasheet HTML 9Page - Holtek Semiconductor Inc HT47C06L Datasheet HTML 10Page - Holtek Semiconductor Inc Next Button
Zoom Inzoom in Zoom Outzoom out
 6 / 37 page
background image
HT47C06L
Rev. 1.00
6
June 15, 2007
When executing a jump instruction, conditional skip ex-
ecution, loading PCL register, subroutine call, initial re-
set, internal interrupt, external interrupt or return from
subroutine, etc., the microcontroller manages program
control by loading the address corresponding to each in-
struction.
For conditional skip instructions, once the condition has
been met, the next instruction, which has already been
fetched during the current instruction execution, is dis-
carded and a dummy cycle replaces it while the proper
instruction is obtained. Otherwise proceed with the next
instruction.
The lower byte of the program counter (PCL) is avail-
able for program control and is a readable and writeable
register (06H). Moving data into the PCL performs a
short jump. The destination will be within 256 locations.
When a control transfer takes place, an additional
dummy cycle is required.
Program Memory
- ROM
The program memory is used to store the program in-
structions, which are to be executed. It also contains
data, table information and interrupt entries, and is orga-
nized into 1024
´16 bits, addressed by the program
counter and table pointer registers.
Certain locations within the program memory are re-
served for special usage:
· Location 000H
This area is reserved for use by the chip reset for pro-
gram initialization. After a chip reset is initiated, the
program will jump to this location and begin execution.
· Location 004H
This area is reserved for the timer/event counter inter-
rupt service program. If timer interrupt results from a
timer/event counter A or B overflow, and if the inter-
rupt is enabled and the stack is not full, the program
will jump to this location and begin execution.
· Location 008H
This area is reserved for the time base interrupt ser-
vice program. If a time base interrupt occurs, and if the
interrupt is enabled and the stack is not full, the pro-
gram will jump to this location and begin execution.
· Table location
Any location within the program memory can be used
as a look-up table where programmers can store fixed
data. The instructions TABRDC [m] (the current page,
1 page=256 words) and TABRDL [m] (the last page)
transfer the contents of the lower-order byte to the
specified data memory, and the higher-order byte to
TBLH(08H). Only the destination of the lower-order
byte in the table is well-defined, the higher-order byte
of the table word are transferred to the TBLH. The ta-
ble higher-order byte (TBLH) is a read only register.
The table pointer (TBLP) is a read/write register(07H),
which indicates the table location. Before accessing
the table, the location must be placed in the TBLP.
The TBLH is read only and cannot be restored. If the
main routine and the ISR (interrupt service routine)
both employ the table read instruction, the contents of
the TBLH in the main routine are likely to be changed
by the table read instruction used in the ISR. Errors
can occur. In other words using the table read instruc-
tion in the main routine and the ISR simultaneously
should be avoided. However, if the table read instruc-
tion has to be applied in both the main routine and the
ISR, the interrupt is supposed to be disabled prior to
the table read instruction. It will not be enabled until
the TBLH has been backed up. All table related in-
structions need two cycles to complete the operation.
These areas may function as normal program mem-
ory depending upon the requirements.
D e v i c e I n i t i a l i z a t i o n P r o g r a m
P r o g r a m
R O M
1 6 b i t s
L o o k - u p T a b l e ( 2 5 6 w o r d s )
N o t e : n r a n g e s f r o m 0 t o 3
T i m e B a s e I n t e r r u p t S u b r o u t i n e
L o o k - u p T a b l e ( 2 5 6 w o r d s )
T i m e r / e v e n t C o u n t e r I n t e r r u p t S u b r o u t i n e
0 0 0 H
0 0 4 H
3 F F H
n 0 0 H
n F F H
0 0 8 H
Program Memory
Instruction(s)
Table Location
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
TABRDC [m]
P9
P8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
1
1
@7
@6
@5
@4
@3
@2
@1
@0
Table Location
Note: *9~*0: Bits of table location
@7~@0: Bits of table pointer
P9
~P8: Bits of current program counter



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com