ADRF6807

Data Sheet

Rev. B | Page 8 of 36

Pin No.

Mnemonic

Description

6

REFIN

Reference Input. Nominal input level is 1 V p-p. Input range is 9 MHz to 160 MHz.

8

MUXOUT

Multiplexer Output. This output can be programmed to provide the reference output signal or the

lock detect signal. The output is selected by programming the appropriate register.

9

DECL2

Connect a 0.1 μF capacitor between this pin and ground.

10

VCC2

3.3 V Power Supply for 2.5 V LDO.

12

DATA

Serial Data Input. The serial data is loaded MSB first with the three LSBs being the control bits.

13

CLK

Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is

latched into the 24-bit shift register on the CLK rising edge. Maximum clock frequency is 20 MHz.

14

LE

Load Enable. When the LE input pin goes high, the data stored in the shift registers is loaded into

one of the six registers, the relevant latch being selected by the first three control bits of the 24-bit word.

17, 34

VCCLO

3.3 V Power Supply for LO Path Blocks.

18, 19

QBBP, QBBN

Demodulator Q-Channel Differential Baseband Outputs (Differential Output Impedance of 28 Ω).

22

VCCBB

5 V Power Supply for Demodulator Blocks.

23

VOCM

Baseband Common-Mode Reference Input; 1.65 V Nominal. It sets the dc common-mode level of

the IBBx and QBBx outputs.

25, 26

RFIP, RFIN

Differential 100 Ω, Internally Biased RF Inputs. These pins must be ac-coupled.

28

VCCRF

5 V Power Supply for Demodulator Blocks.

29

DECL3

Connect a 2.2 μF capacitor between this pin and ground.

32, 33

IBBN, IBBP

Demodulator I-Channel Differential Baseband Outputs (Differential Output Impedance of 28 Ω).

36

LOSEL

LO Select. Connect this pin to ground for the simplest operation and to completely control the LO

path and input/output direction from the register programming of the SPI.

For additional control without register reprogramming, this input pin can determine whether the

LOP and LON pins operate as inputs or outputs. LOP and LON become inputs if the LOSEL pin is set

low, the LDRV bit of Register 5 is set low, and the LXL bit of Register 5 is set high. The externally

applied LO drive must be at M×LO frequency (where M corresponds to the main LO divider setting). LON

and LOP become outputs when LOSEL is high or if the LDRV bit of Register 5 (DB3) is set high and

the LXL bit of Register 5 (DB4) is set to low. The output frequency is controlled by the LO output

divider bits in Register 7. This pin should not be left floating.

37, 38

LON, LOP

Local Oscillator Input/Output (Differential Output Impedance of 28 Ω). When these pins are used as

output pins, a differential frequency divided version of the internal VCO is available on these pins.

When the internal LO generation is disabled, an external M×LO frequency signal can be applied to

these pins, where M corresponds to the main divider setting.

39

VTUNE

VCO Control Voltage Input. This pin is driven by the output of the loop filter. The nominal input

voltage range on this pin is 1.0 V to 2.8 V.

40

DECL1

Connect a 10 μF capacitor between this pin and ground as close to the device as possible because

this pin serves as the VCO supply and loop filter reference.

EP

Exposed Paddle. The exposed paddle should be soldered to a low impedance ground plane.