| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DAC8563SDGST bảng dữ liệu(PDF) 41 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
DAC8563SDGST bảng dữ liệu(HTML) 41 Page - Texas Instruments |
|
41 / 56 page ![]() P1.4/GPIO P1.5/SCLK P1.6/SDO MSP430F2013 SYNC DAC SCLK D IN NOTE: Additionalpinsomittedforclarity. TMS320F28062 MFSxA MCLKxA MDxA SYNC DAC SCLK D IN NOTE: Additionalpinsomittedforclarity. FSx0 CLKx0 Dx0 SYNC DAC SCLK D IN NOTE: Additionalpinsomittedforclarity. OMAP-L138 DAC8562, DAC8563 DAC8162, DAC8163 DAC7562, DAC7563 www.ti.com SLAS719C – AUGUST 2010 – REVISED JUNE 2011 MICROPROCESSOR INTERFACING DAC756x/DAC816x/DAC856x to an MSP430 USI Interface Figure 97 shows a serial interface between the DAC756x, DAC816x, or DAC856x and a typical MSP430 USI port such as the one found on the MSP430F2013. The port is configured in SPI master mode by setting bits 3, 5, 6, and 7 in USICTL0. The USI counter interrupt is set in USICTL1 to provide an efficient means of SPI communication with minimal software overhead. The serial clock polarity, source, and speed are controlled by settings in the USI clock control register (USICKCTL). The SYNC signal is derived from a bit-programmable pin on port 1; in this case, port line P1.4 is used. When data are to be transmitted to the DAC756x, DAC816x, or DAC856x, P1.4 is taken low. The USI transmits data in 8-bit bytes; thus, only eight falling clock edges occur in the transmit cycle. To load data to the DAC, P1.4 is left low after the first eight bits are transmitted; then, a second write cycle is initiated to transmit the second byte of data. P1.4 is taken high following the completion of the third write cycle. Figure 97. DAC756x/DAC816x/DAC856x to MSP430 Interface DAC756x/DAC816x/DAC856x to a TMS320 McBSP Interface Figure 98 shows an interface between the DAC756x, DAC816x, or DAC856x and any TMS320 series DSP from Texas Instruments with a multi-channel buffered serial port (McBSP). Serial data are shifted out on the rising edge of the serial clock and are clocked into the DAC756x, DAC816x, or DAC856x on the falling edge of the SCLK signal. Figure 98. DAC756x/DAC816x/DAC856x to TMS320 McBSP Interface DAC756x/DAC816x/DAC856x to an OMAP-L1x Processor Figure 99 shows a serial interface between the DAC756x/DAC816x/DAC856x and the OMAP-L138. The transmit clock CLKx0 of the L138 drives SCLK of the DAC756x, DAC816x, or DAC856x, and the data transmit (Dx0) output drives the serial data line of the DAC. The SYNC signal is derived from the frame sync transmit (FSx0) line, similar to the TMS320 interface. Figure 99. DAC756x/DAC816x/DAC856x to OMAP-L1x Processor Copyright © 2010–2011, Texas Instruments Incorporated Submit Documentation Feedback 41 Product Folder Link(s): DAC8562 DAC8563 DAC8162 DAC8163 DAC7562 DAC7563 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |