| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DAC8563SDGST bảng dữ liệu(PDF) 35 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
DAC8563SDGST bảng dữ liệu(HTML) 35 Page - Texas Instruments |
|
35 / 56 page ![]() DAC8562, DAC8563 DAC8162, DAC8163 DAC7562, DAC7563 www.ti.com SLAS719C – AUGUST 2010 – REVISED JUNE 2011 SOFTWARE RESET FUNCTION The DAC756x, DAC816x, and DAC856x contain a software reset feature. The software reset function uses command 101. The software reset command contains two reset modes which are software-programmable by setting bit DB0 in the shift register. Table 13 and/or Table 19 and Table 20 show the available software reset commands. Table 19. Software Reset Command Structure Command Address Data X X 1 0 1 X X X X X X X X X X X X X X X X X X RST DB23 DB0 Table 20. Software Reset RST (DB0) Registers Reset to Default Values 0 DAC registers Input registers 1 DAC registers Input registers LDAC registers Power-down registers Internal reference register Gain registers LDAC FUNCTIONALITY The DAC756x, DAC816x, and DAC856x offer both a software and hardware simultaneous update and control function. The DAC double-buffered architecture has been designed so that new data can be entered for each DAC without disturbing the analog outputs. DAC756x, DAC816x, and DAC856x data updates can be performed either in synchronous or in asynchronous mode. In asynchronous mode, the LDAC pin is used as a negative edge-triggered timing signal for simultaneous DAC updates. Multiple single-channel writes can be done in order to set different channel buffers to desired values and then make a falling edge on LDAC pin to simultaneously update the DAC output registers. Data buffers of all channels must be loaded with desired data before an LDAC falling edge. After a high-to-low LDAC transition, all DACs are simultaneously updated with the last contents of the corresponding data buffers. If the content of a data buffer is not changed, the corresponding DAC output remains unchanged after the LDAC pin is triggered. LDAC must be returned high before the next serial command is initiated. In synchronous mode, data are updated with the falling edge of the 24th SCLK cycle, which follows a falling edge of SYNC. For such synchronous updates, the LDAC pin is not required, and it must be connected to GND permanently or asserted and held low before sending commands to the device. Copyright © 2010–2011, Texas Instruments Incorporated Submit Documentation Feedback 35 Product Folder Link(s): DAC8562 DAC8563 DAC8162 DAC8163 DAC7562 DAC7563 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |