SC28L92 datasheet(49/73 Pages) NXP

49 / 73 page

SC28L92_7

Product data sheet

Rev. 07 — 19 December 2007

49 of 73

NXP Semiconductors

SC28L92

3.3 V/5.0 V Dual Universal Asynchronous Receiver/Transmitter

The counter ready status bit (ISR[3]) is set once each cycle of the square wave. The bit is

reset by a stop counter command (read with A3 to A0 = 1111). The command however,

does not stop the C/T. The generated square wave is output on OP3 if it is programmed to

be the C/T output. In the counter mode, the value C/T loaded into CTPU and CTPL by the

CPU is counted down to 0. Counting begins upon receipt of a start counter command.

Upon reaching terminal count 0x0000, the counter ready interrupt bit (ISR[3]) is set. The

counter continues counting past the terminal count until stopped by the CPU. If OP3 is

programmed to be the output of the C/T, the output remains HIGH until terminal count is

reached, at which time it goes LOW. The output returns to the HIGH state and ISR[3] is

cleared when the counter is stopped by a stop counter command. The CPU may change

the values of CTPU and CTPL at any time, but the new count becomes effective only on

the next start counter commands. If new values have not been loaded, the previous count

values are preserved and used for the next count cycle.

In the counter mode, the current value of the upper and lower 8 bits of the counter (CTU,

CTL) may be read by the CPU. It is recommended that the counter be stopped when

reading to prevent potential problems which may occur if a carry from the lower 8 bits to

the upper 8 bits occurs between the times that both halves of the counter are read.

However, note that a subsequent start counter command will cause the counter to begin a

new count cycle using the values in CTPU and CTPL.

When the C/T clock divided by 16 is selected, the maximum divisor becomes 1,048,575.

7.4 Output port notes

The output ports are controlled from four places: the OPCR register, the OPR register, the

MR registers and the command register (except the SCC2681 and SCC68681). The

OPCR register controls the source of the data for the output ports OP2 to OP7. The data

source for output ports OP0 and OP1 is controlled by the MR and CR registers. When the

OPR is the source of the data for the output ports, the data at the ports is inverted from

that in the OPR register.

The content of the OPR register is controlled by the Set Output Port bits command and

the Reset Output Port bits command. These commands are at 0xE and 0xF, respectively.

When these commands are used, action takes place only at the bit locations where ones

exist. For example, a logic 1 in bit location 5 of the data word used with the Set Output

Port bits command will result in OPR5 being set to one. The OP5 would then be set to

logic 0 (VSS). Similarly, a logic 1 in bit position 5 of the data word associated with the

Reset Output Ports bits command would set OPR5 to logic 0 and, hence, the pin OP5 to a

logic 1 (VDD).

7.5 The CTS, RTS, CTS enable Tx signals

Clear To Send (CTS) is usually meant to be a signal to the transmitter meaning that it may

transmit data to the receiver. The CTS input is on pin IP0 for TxA and on IP1 for TxB. The

CTS signal is active LOW; thus, it is called CTSAN for TxA and CTSBN for TxB. RTS is

usually meant to be a signal from the receiver indicating that the receiver is ready to

receive data. It is also active LOW and is, thus, called RTSAN for RxA and RTSBN for

RxB. RTSAN is on pin OP0 and RTSBN is on OP1. A receiver’s RTS output will usually be

connected to the CTS input of the associated transmitter. Therefore, one could say that

RTS and CTS are different ends of the same wire.

SC28L92 bảng dữ liệu(PDF) 49 Page - NXP Semiconductors

SC28L92 bảng dữ liệu(HTML) 49 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

bảng dữ liệu tải về

Link URL