LPC2917SLASH01 datasheet(30/86 Pages) NXP

30 / 86 page

LPC2917_19_01_2

Preliminary data sheet

Rev. 02 — 17 June 2009

30 of 86

NXP Semiconductors

LPC2917/01; LPC2919/01

ARM9 microcontroller with CAN and LIN

• Up to four external outputs per timer corresponding to match registers, with the

following capabilities:

– Set LOW on match

– Set HIGH on match

– Toggle on match

– Do nothing on match

• Pause input pin (MSCSS timers only)

The timers are designed to count cycles of the clock and optionally generate interrupts or

perform other actions at speciﬁed timer values, based on four match registers. They also

include capture inputs to trap the timer value when an input signal changes state,

optionally generating an interrupt. The core function of the timers consists of a 32 bit

prescale counter triggering the 32 bit timer counter. Both counters run on clock

CLK_TMRx (x runs from 0 to 3) and all time references are related to the period of this

clock. Note that each timer has its individual clock source within the Peripheral

SubSystem. In the Modulation and Sampling SubSystem each timer also has its own

individual clock source. See section Section 6.15.5 for information on generation of these

clocks.

6.12.3.1

Pin description

The four timers in the peripheral subsystem of the LPC2917/2919/01 have the pins

described below. The two timers in the modulation and sampling subsystem have no

external pins except for the pause pin on MSCSS timer 1. See Section 6.14.6 for a

description of these timers and their associated pins. The timer pins are combined with

other functions on the port pins of the LPC2917/2919/01, see Section 6.11.3. Table

Table 15 shows the timer pins (x runs from 0 to 3).

6.12.3.2

Clock description

The timer modules are clocked by two different clocks; CLK_SYS_PESS and CLK_TMRx

(x = 0-3), see Section 6.7.2. Note that each timer has its own CLK_TMRx branch clock for

power management. The frequency of all these clocks is identical as they are derived from

the same base clock BASE_CLK_TMR. The register interface towards the system bus is

clocked by CLK_SYS_PESS. The timer and prescale counters are clocked by

CLK_TMRx.

Table 15.

Timer pins

Symbol

Pin name

Direction

Description

TIMERx CAP[0]

CAPx[0]

TIMER x capture input 0

TIMERx CAP[1]

CAPx[1]

TIMER x capture input 1

TIMERx CAP[2]

CAPx[2]

TIMER x capture input 2

TIMERx CAP[3]

CAPx[3]

TIMER x capture input 3

TIMERx MAT[0]

MATx[0]

OUT

TIMER x match output 0

TIMERx MAT[1]

MATx[1]

OUT

TIMER x match output 1

TIMERx MAT[2]

MATx[2]

OUT

TIMER x match output 2

TIMERx MAT[3]

MATx[3]

OUT

TIMER x match output 3

LPC2917/01 bảng dữ liệu(PDF) 30 Page - NXP Semiconductors

LPC2917/01 bảng dữ liệu(HTML) 30 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

bảng dữ liệu tải về

Link URL