M16CSLASH62 datasheet(192/621 Pages) RENESAS

192 / 621 page

Mitsubishi microcomputers

M16C / 62 Group

SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

Usage precaution

177

Timer A (timer mode)

Usage Precaution

Timer A (event counter mode)

(1) Reading the timer Ai register while a count is in progress allows reading, with arbitrary timing, the

value of the counter. Reading the timer Ai register with the reload timing gets “FFFF16” by underflow

or “000016” by overflow. Reading the timer Ai register after setting a value in the timer Ai register with

a count halted but before the counter starts counting gets a proper value.

(2) When stop counting in free run type, set timer again.

(1) Reading the timer Ai register while a count is in progress allows reading, with arbitrary timing, the

value of the counter. Reading the timer Ai register with the reload timing gets “FFFF16”. Reading the

timer Ai register after setting a value in the timer Ai register with a count halted but before the counter

starts counting gets a proper value.

(1) Setting the count start flag to “0” while a count is in progress causes as follows:

• The counter stops counting and a content of reload register is reloaded.

• The TAiOUT pin outputs “L” level.

• The interrupt request generated and the timer Ai interrupt request bit goes to “1”.

(2) The timer Ai interrupt request bit goes to “1” if the timer's operation mode is set using any of the

following procedures:

• Selecting one-shot timer mode after reset.

• Changing operation mode from timer mode to one-shot timer mode.

• Changing operation mode from event counter mode to one-shot timer mode.

Therefore, to use timer Ai interrupt (interrupt request bit), set timer Ai interrupt request bit to “0”

after the above listed changes have been made.

Timer A (one-shot timer mode)

(1) The timer Ai interrupt request bit becomes “1” if setting operation mode of the timer in compliance with

any of the following procedures:

• Selecting PWM mode after reset.

• Changing operation mode from timer mode to PWM mode.

• Changing operation mode from event counter mode to PWM mode.

Therefore, to use timer Ai interrupt (interrupt request bit), set timer Ai interrupt request bit to “0”

after the above listed changes have been made.

(2) Setting the count start flag to “0” while PWM pulses are being output causes the counter to stop

counting. If the TAiOUT pin is outputting an “H” level in this instance, the output level goes to “L”, and

the timer Ai interrupt request bit goes to “1”. If the TAiOUT pin is outputting an “L” level in this instance,

the level does not change, and the timer Ai interrupt request bit does not becomes “1”.

Timer A (pulse width modulation mode)

Timer B (timer mode, event counter mode)

(1) Reading the timer Bi register while a count is in progress allows reading , with arbitrary timing, the

value of the counter. Reading the timer Bi register with the reload timing gets “FFFF16”. Reading the

timer Bi register after setting a value in the timer Bi register with a count halted but before the counter

starts counting gets a proper value.

M16C/62 bảng dữ liệu(PDF) 192 Page - Renesas Technology Corp

M16C/62 bảng dữ liệu(HTML) 192 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL