M16CSLASH1N datasheet(131/238 Pages) RENESAS

131 / 238 page

Rev.1.00

Oct 20, 2004

page 119 of 222

M16C/1N Group

13. Serial I/O

REJ09B0007-0100Z

Figure 13.11 UARTi transmit/receive mode register in UART mode

b5 b4

UARTi transmit/receive mode registers

SMD0

Serial I/O mode select bit

CKDIR

Internal / external clock

select bit

0 : Internal clock

1 : External clock (Note 1)

STPS

Stop bit length select bit

0 : One stop bit

1 : Two stop bits

PRYE

Parity enable bit

0 : Parity disabled

1 : Parity enabled

Reserved bit

Set to "0"

PRY

Odd / even parity

select bit

Valid when bit 6 = "1"

0 : Odd parity

1 : Even parity

SMD1

SMD2

Symbol

UiMR (i=0,1)

Address

00A016, 00A816

When reset

0016

Function

Bit name

Bit symbol

Note 1: Set the corresponding port direction register to "0".

b2 b1 b0

1 0 0 : Transfer data 7 bits long

1 0 1 : Transfer data 8 bits long

1 1 0 : Transfer data 9 bits long

Function

Pin name

Method of selection

Remarks

Serial data output

Serial data input

Transfer clock input

TxD0 (P14)

TxD1 (P37)

RxD0 (P15)

RxD1 (P35)

RxD1 (P37)

CLKi (P16, P36)

RxD1 input pin select bit

(bit 6 at address 00B016)="1"

Port P15 direction register

(bit 5 at address 00E316)="0"

Port P35 direction register

(bit 5 at address 00E716)="0"

RxD1 input pin select bit

(bit 6 at address 00B016)="1"

Port P37 direction register

(bit 7 at address 00E716)="0"

RxD1 input pin select bit

(bit 6 at address 00B016)="0"

Internal/external clock select bit

(bit 3 at address 00A016 and

00A816)="1"

Ports P16 and P36 direction

and 00E716)="0"

Port P14 cannot be used as an I/O port even when

performing only serial data input but not serial data output.

Port P37 cannot be used as an I/O port even when

performing only serial data input but not serial data output.

Port P15 can be used as an I/O port when performing only

serial data output but not serial data input.

Port P35 can be used as an I/O port when performing only

serial data output but not serial data input.

When setting Port P37 as RxD1, serial data output cannot

be performed.

Port P35 can be used as an I/O port.

Ports P16 and P36 can be used as an I/O port when not

performing transfer clock input. In this case, set the

internal/external clock select bit to "0".

Table 13.4 lists the functions of the input/output pins during UART mode. Note that for a period from when

the UARTi operation mode is selected to when transfer starts, the TxDi pin outputs a "H". (If the N-

channel open-drain is selected, this pin is in floating state.)

Table 13.4 Input/output pin functions in UART mode

M16C/1N bảng dữ liệu(PDF) 131 Page - Renesas Technology Corp

M16C/1N bảng dữ liệu(HTML) 131 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL