ST75C530 datasheet(44/84 Pages) STMICROELECTRONICS

44 / 84 page

VIII.1.3 - CR Command

Issuing a CR command causes the ST75C530/540 to dump a specific memory location in complex mode.

This instruction is particularly useful for equalizer state analysis or for software eye-pattern display. The

report area has this meaning :

RP7

RP6

RP5

RP4

RP3

RP2

RP1

RP0

COMREP[0]

IP7

IP6

IP5

IP4

IP3

IP2

IP1

IP0

COMREP[1]

RP0..RP7 is the MSB part of the 16-bit value of the real part and IP0..IP7is the MSB part of the imaginary

part. The CR command insures that the real and imaginary part of the desired complex value are sampled

internally at the same time. The address given in the parameter field of CR is the address of the real part.

VIII.1.4 - MR/TDRC/TDRW/IDT/MRI/MRLO Commands

The report issued by the MR/TDRC/TDRW/IDT/MRI/MRLO commands follow the same rules as for CR.

The report meaning is :

COMREP[0]

D15

D14

D13

D12

D11

D10

COMREP[1]

D0..D15 is the 16-bit value requested by the command.

In the case of IDT,D15..D12 containsthe productidentification(3 for ST75C530,7 for ST75C5540), D11..D8

contains the hardware revision identification and D7..D0 contains the software revision identification.

VIII.2 - Modem Status

VIII.2.1 - Modem Status Description

The Status of ST75C530/540 is divided into 4 fields :

- The error status byte SYSERR that provides information about error. This status can trigger an IT0

interrupt,

- The general status byte STATUS[0] and STATUS[1] that contains all the modem signals. These status

bytes can trigger an IT4 interrupt,

- The quality status STAQUA, that contains the quality of the received transmission,

- The optional status bytes STAOP[0], STAOP[1], STAOP[2] and STAOP[3], that contains additional

information regarding the ST75C530/540 operating mode. This default information can be changed to

monitor any internal variables using the DOSR command.

All these informations are updated on a Baud basis :

Mode

Baud Rate

(2) (Hz)

V.32bis/V.32 (ST75C540 only)

2400

V.22bis/V.22/Bell 212A (ST75C540 only)

2400

Tone

2400

Bell 103 (full duplex)

2400

V.21 (full duplex)

2400

V.23 (full duplex)

2400

V.27ter 2400bps

1200

V.27ter 4800bps

1600

(1)

V.29

2400

V.17/V.33

2400

V.21 channel 2

2400

HANDSET, CODER or DECODER Modes

1200

Notes : 1. In this mode the tone detectors outputs are update 800 times by second.

2. This baud rate defines also, the maximum command rate. Each baud time the ST75C530/540 looks at the COMSYS location

(Address $00) to see if a command have been sent by the host processor. If the content of this location is different from zero the

ST75C530/540 execute the command.

VIII - STATUS DESCRIPTION (continued)

ST75C530 - ST75C540

44/84

ST75C530 bảng dữ liệu(PDF) 44 Page - STMicroelectronics

ST75C530 bảng dữ liệu(HTML) 44 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

bảng dữ liệu tải về

Link URL