FXLS8961AF datasheet(94/101 Pages) NXP

94 / 101 page

NXP Semiconductors

FXLS8961AF

3-Axis Low-g Accelerometer

Document ID

Release date

Description

– Conditions, Min, Typ, Max: removed Z axis in the condition fields and

removed the Min, Typ, and Max values.

– Footnote 1: revised footnote from "Determined with post board mount data

using a standard lead-free reflow profile and NXP recommended landing

pattern on a 2-layer FR4 PCB with 1.2 mm (47 mil) overall thickness." to

"Determined with post board mount data using a standard lead-free reflow

profile and NXP recommended landing pattern on a 10-layer FR4 PCB with

1.6 mm (63 mil) overall thickness."

– Footnote 2: revised footnote from "Based on characterization data on limited

number of parts from 3 lots" to "Based on characterization data on limited

number of parts from 3 lots. Limits provided with 5 sigma margin and 95%

confidence level."

• Section 9.1, inserted new section, content and images.

• Section 10, Table 8, revised as follows:

– IDDHPM: revised the Typ value from "150" to "146.9" where the condtion is

ODR independent,T = 25 °C.

– IDDLPM where T = 25 °C: revised all Typ values where the condtion is T =

25 °C from "150, 75, 38, 20, 11, 5.3, 3.1, 1.8, 1.4, 1.0, 0.80, 0.70, and 0.65"

to "146.9, 73.9, 37.5, 19.4, 10.4, 5.88, 3.63, 2.50, 2.10, 1.74, 1.56, 1.47 and

1.42" and revised all Max values from "200, 100, 53, 30, 20, 10, 7, 4, 2.5,

2.0, 1.5, 1.5 and 1.5" to "200, 100, 53, 30, 20, 10.5, 7.5, 4.8, 3.3, 2.8, 2.4,

2.3, and 2.2".

– IDDSTBY: revised the Typ value where the condtion is T = 25 °C from "0.60"

to "1.01" and Max value from "1.5" to "2.0".

– IDDLPM: revised the Max values for 100 Hz to 0.781 Hz from "13, 10, 8, 4, 4,

4, 4, and 4" to "13.7, 10.7, 8.7, 4.8, 4.8, 4.8, 4.8 and 4.8".

– IDDSTBY: revised the Max value from "4" to 4.5".

• Section 15.2.9, revised "...factory programmed to 87h..." to "…factory

programmed to 81h.…", and Reset bits 2 and 1 from "1" to "0".

• Section 15.3.3, Table 52 and Table 53, removed the columns titled "Noise RMS

(mg)" and "IDD (µA)" and the associated footnotes.

• Section 16.3, Figure 22, Figure 23, Figure 25, Figure 26, and Figure 27,

updating the graphic registration number, no content change to the images.

• Section 16.3, Figure 24, revised "C2 0.1 µF" to "C1 0.1 µF" and updated the

graphic registration number.

• Section 17.1, updated the package outline drawing images in Figure 28,

Figure 29, and Figure 30.

• Section 19.1, updated the images in Figure 31, Figure 32, and Figure 33.

• Section 19.1, inserted note at the end of the section.

• Section 20, Cross-axis sensitivity: Removed "The cross-axis sensitivity

specification represents the maximum of these six terms." from the description.

FXLS8961AF v.1

28 November 2022

• FXLS8961AF v.1 is an objective data sheet.

• Initial release.

Table 122. Revision history...continued

FXLS8961AF

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 2.1 — 7 March 2024

94 / 101

FXLS8961AF bảng dữ liệu(PDF) 94 Page - NXP Semiconductors

FXLS8961AF bảng dữ liệu(HTML) 94 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL