| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
NRF52820-QDAA-R bảng dữ liệu(PDF) 178 Page - Nordic Semiconductor |
|
|
|||||||||||||||||||||||||||||
NRF52820-QDAA-R bảng dữ liệu(HTML) 178 Page - Nordic Semiconductor |
|
178 / 437 page ![]() Peripherals The two last octets contain the 16-bit ITU-T CRC. The FCS is calculated over the MAC header (MHR) and MAC payload (MSDU) parts of the frame. This field is calculated automatically when sending a frame, or indicated in the CRCSTATUS register when a frame is received. If configured, this feature is taken care of autonomously by the CRC module. 6.12.13.2 Operating frequencies The IEEE 802.15.4 standard defines 16 channels, 11 - 26, of 5 MHz each, in the 2450 MHz frequency band. To choose the correct channel center frequency, the FREQUENCY register must be programmed according to the table below. IEEE 802.15.4 channel Center frequency (MHz) FREQUENCY setting Channel 11 2405 5 Channel 12 2410 10 Channel 13 2415 15 Channel 14 2420 20 Channel 15 2425 25 Channel 16 2430 30 Channel 17 2435 35 Channel 18 2440 40 Channel 19 2445 45 Channel 20 2450 50 Channel 21 2455 55 Channel 22 2460 60 Channel 23 2465 65 Channel 24 2470 70 Channel 25 2475 75 Channel 26 2480 80 Table 61: IEEE 802.15.4 center frequency definition 6.12.13.3 Energy detection (ED) As required by the IEEE 802.15.4 standard, it must be possible to sample the received signal power within the bandwidth of a channel, for the purpose of determining presence of activity. To prevent the channel signal from being decoded, the shortcut between the READY event and the START task should be disabled before putting the RADIO in receive mode. The energy detection (ED) measurement time, where RSSI samples are averaged, is 8 symbol periods, corresponding to 128 µs. The standard further specifies the measurement to be a number between 0 and 255, where 0 shall indicate received power less than 10 dB above the selected receiver sensitivity. The power range of the ED values must be at least a 40 dB linear mapping with accuracy of ±6 dB. See section 6.9.7 Receiver ED in the IEEE 802.15.4 standard for further details. The following example shows how to perform a single energy detection measurement and convert to IEEE 802.15.4 scale. 4463_156 v1.0 178 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |